Search found 12 matches
- Sat, Mar 17 2007, 10:07AM
- Forum: eCabinet Systems Software
- Topic: Reverse Isometric View
- Replies: 9
- Views: 7278
When I learned drafting years ago with a lead lock, T-square and 30-60-90 triangle :? an Isometric view was 3 sided orthographic no perspective, On the screen or on paper the back and far end looked longer than it's respective counterpart but you could verifiy it was the same length with a scale. If...
- Sat, Mar 10 2007, 3:58PM
- Forum: eCabinet Systems Software
- Topic: Just a tad frustrated
- Replies: 6
- Views: 5521
- Tue, Mar 06 2007, 12:30PM
- Forum: eCabinet Systems Software
- Topic: Attn: Ken Susnjara
- Replies: 3
- Views: 3498
Thanks for the reply Dan You answered one question I was having right off the bat, if the mobo needs the processor to boot :o I had disconnected the power leads last night and reconnected them this morning and it booted up, I will check the voltages next, I had already replaced the mobo once due to ...
- Tue, Mar 06 2007, 10:56AM
- Forum: eCabinet Systems Software
- Topic: Attn: Ken Susnjara
- Replies: 3
- Views: 3498
Hello Dan My sympathies for the time you hand to take about the trojan, and congradulations for beating it, and cheers to Dean. After reading your post I was just curious about the problem, if you got it others will too, and in your search for info did it say it will become part of a virus definitio...
- Fri, Mar 02 2007, 8:26PM
- Forum: eCabinet Systems Software
- Topic: Off Topic - Life is good again
- Replies: 49
- Views: 32357
- Wed, Feb 28 2007, 7:33PM
- Forum: eCabinet Systems Software
- Topic: double post appaering
- Replies: 2
- Views: 3153
- Thu, Feb 15 2007, 4:27PM
- Forum: eCabinet Systems Software
- Topic: Batch Cabinet & Nesting question
- Replies: 0
- Views: 2659
Batch Cabinet & Nesting question
Thought I would try to use batch cabinets instead of cutom layout like I usually do. Everything seemed OK but then I noticed when I went to the sheet Layout (nesting) that in filters and on the layout I only had one of each cabinet even though I had 2 cabinets (assemblies) with a quantity of 2. Is t...
- Sat, Jan 20 2007, 2:47PM
- Forum: eCabinet Systems Software
- Topic: Default wood type?
- Replies: 19
- Views: 17048
- Tue, Jan 16 2007, 7:28PM
- Forum: eCabinet Systems Software
- Topic: Newbie's first post---HELP!!!!?
- Replies: 12
- Views: 11286
Wayne Kind of a hard way but you can create (add) a new sheet and the just copy and paste the indidual cabinets from the 1st sheet w/ the wall layout to the new sht. that way you don't show any walls or floors. Just don't size any of them before you finish pasting (shift>left mouse) I tried selectin...
- Tue, Jan 16 2007, 5:54PM
- Forum: eCabinet Systems Software
- Topic: Newbie's first post---HELP!!!!?
- Replies: 12
- Views: 11286
Wayne Dan's right, printer setup in software. I knew what I wanted to say, but it didn't come out right, last time I tried to help I wrote an essay and, after looking at it, thought I would tone a reply down, guess a little to much :roll: Maybe I'll get this forum thing right eventually. Good luck o...
- Mon, Jan 15 2007, 8:54PM
- Forum: eCabinet Systems Software
- Topic: Newbie's first post---HELP!!!!?
- Replies: 12
- Views: 11286
- Thu, Dec 28 2006, 2:48PM
- Forum: eCabinet Systems Software
- Topic: Detached Toe Base selection
- Replies: 19
- Views: 22794
Hello Joe I use the detached toe because when I build my cabinets I make the toe completly seperate from the box. (I hand build all my cabinets, no router yet :( ) When using it you have to create a seperate cabinet (toe) the height of your toe and then join the two cabinets together to make an assy...