Search found 245 matches

by Mark Taylor
Wed, Aug 06 2008, 8:40PM
Forum: Design Sharing
Topic: Italian Renaissance Credenza
Replies: 38
Views: 22160

Re: Italian Renaissance Credenza

Yes, Dan, I believe they are both one in the same.
by Mark Taylor
Tue, Aug 05 2008, 8:29PM
Forum: Design Sharing
Topic: Italian Renaissance Credenza
Replies: 38
Views: 22160

Re: Italian Renaissance Credenza

that would be clearly beyond my capabilities....I can't even figure out how to program the buttons on the radio in my car - when did they stop pulling out? Hell, I can't even get a hold of them with my fingernails... :roll:
by Mark Taylor
Mon, Aug 04 2008, 7:03PM
Forum: Design Sharing
Topic: Italian Renaissance Credenza
Replies: 38
Views: 22160

Re: Italian Renaissance Credenza

Joe...
I would guess it should be easy enough to find a reed switch or pressure switch from grainger which could be set to detect the unit in the lower position to disconnect the electricity.
Mark
by Mark Taylor
Thu, Jul 24 2008, 9:37PM
Forum: Design Sharing
Topic: Italian Renaissance Credenza
Replies: 38
Views: 22160

Re: Italian Renaissance Credenza

Mike are you referring to the direct wired switch?

I guess I've only used the remote - and you don't have to hold the button on it.

We never mounted the direct wired switch...seems like with our society if you don't have a remote, they wouldn't use it anyway.

Mark
by Mark Taylor
Tue, Jul 15 2008, 10:10PM
Forum: Design Sharing
Topic: Italian Renaissance Credenza
Replies: 38
Views: 22160

Re: Italian Renaissance Credenza

Hey Joe... I do have an ecabinets file of the walnut credenza, when we built it - I was not happy with the moldings shown on the ecabinets drawing once we cut them. So we actually modified the one we built from the drawings and I haven't ever gone back in and modified the drawings to reflect the act...
by Mark Taylor
Mon, Jul 14 2008, 1:08AM
Forum: Design Sharing
Topic: Italian Renaissance Credenza
Replies: 38
Views: 22160

Re: Italian Renaissance Credenza

Joe, I can only speak to the whisper lift... when we designed and built the walnut credenza for a show we decided to try the whisper lift (basically due to cost). It performs beautifully and is still functioning in the showroom today. It is a simple design with a bosch motor - there is little to go ...
by Mark Taylor
Wed, Jun 11 2008, 8:44PM
Forum: eCabinet Systems Software
Topic: eCabinets Made Easy
Replies: 8
Views: 1063

Re: eCabinets Made Easy

me second!

Mark
by Mark Taylor
Thu, Jun 05 2008, 9:47PM
Forum: eCabinet Systems Software
Topic: seating help
Replies: 3
Views: 518

Re: seating help

thanks for the suggestions...I have asked her to consult an upholstery person - that makes the most sense to me!

Mark
by Mark Taylor
Wed, Jun 04 2008, 9:47PM
Forum: eCabinet Systems Software
Topic: seating help
Replies: 3
Views: 518

seating help

We have a customer were building seating in their new theatre...the architect has designed simple settee type seating around the perimeter of the room. The interior designer does not want flat plywood seats for the cushions. Has anyone created built-in seating with an open seat and some type of stra...
by Mark Taylor
Mon, Jun 02 2008, 9:28PM
Forum: eCabinet Systems Software
Topic: eCabs Mag
Replies: 6
Views: 850

Re: eCabs Mag

I've seen the format...cabinetmaker magazine and several others are published this way. I'm sure there are many advantages to this new format - regardless of the cost of mailing...

Good Form Ken!

Mark
by Mark Taylor
Wed, May 21 2008, 9:27PM
Forum: eCabinet Systems Software
Topic: Molding
Replies: 2
Views: 437

Re: Molding

Sergio... obviously as you have figured out that would be a difficult accessory to make...but if the molding you have here works you can simply load it into the display part editor - add texture etc and then save it to a directory. At that point you can load it into the cabinet editor and resize it ...
by Mark Taylor
Mon, Apr 28 2008, 12:12PM
Forum: eCabinet Systems Software
Topic: Sign up sheet for Programer and tech support day
Replies: 26
Views: 2579

Re: Sign up sheet for Programer and tech support day

Thanks for taking care of it Mike....
by Mark Taylor
Sun, Apr 13 2008, 8:06PM
Forum: eCabinet Systems Software
Topic: Sort of Off Topic and a Rant
Replies: 15
Views: 1989

Re: Sort of Off Topic and a Rant

I always try to live by the golden rule...even though in business is sometimes doesn't make sense or isn't easy to do. About two weeks ago, we had a similar call - it happen to be the third one like that this particular week. We had helped both the other two and I was reallying feeling the pinch tha...
by Mark Taylor
Wed, Apr 09 2008, 9:09PM
Forum: Thermwood 3-Axis Machinery
Topic: arched casings
Replies: 4
Views: 716

Re: arched casings

Hey Will....

We've used profile modeler to cut a variety of curved parts, moldings - etc.

why do you ask?

Mark

Go to advanced search