Search found 205 matches

by DanFecteau
Sun, Mar 03 2019, 11:42AM
Forum: Thermwood 3-Axis Machinery
Topic: Machining 2 3/4'' thick solid oak
Replies: 3
Views: 808

Machining 2 3/4'' thick solid oak

Hello all. We have to rout full depth 1 5/8'' grooves in a solid oak 2 3/4'' thick piece. We have a lot to do. Problem I have right now is that I get a lot of vibration due to the tool lenght I think….I'm using a 3/4'' diameter Onsrud 60-277. I have 18 grooves of 17 1/2'' long to machine on each pie...
by DanFecteau
Sat, Feb 02 2019, 11:21AM
Forum: eCabinet Systems Software
Topic: Tooling of part editor cuts
Replies: 9
Views: 2089

Re: Tooling of part editor cuts

The order means Something ? I thought it always used the largest tool set ?
by DanFecteau
Tue, Jan 29 2019, 9:31AM
Forum: eCabinet Systems Software
Topic: Machining single side material
Replies: 6
Views: 1313

Re: Machining single side material

I Don't know about other guys but I'd rather lose a little bit of yield than having to machine flip parts...
by DanFecteau
Mon, Jan 28 2019, 7:51PM
Forum: eCabinet Systems Software
Topic: Machining single side material
Replies: 6
Views: 1313

Re: Machining single side material

And to also clarify for the operator, at the machine when loading, it would say something like "load sheet good side up" or
flip OP 1st side, load good side down (or up)?

Yes, that's exactly what we would need ! If not I don't see any use for single option in my mind !
by DanFecteau
Sun, Jan 27 2019, 10:02AM
Forum: eCabinet Systems Software
Topic: Tooling of part editor cuts
Replies: 9
Views: 2089

Re: Tooling of part editor cuts

I have the same issue ! I will adjust my max depth too so machine has to use my outline tool to do thru outline cuts. It would be nice to have an option in control nesting to tell to Always use outline tool to do all tru cuts and pockets !
by DanFecteau
Sun, Jan 27 2019, 9:21AM
Forum: eCabinet Systems Software
Topic: Machining single side material
Replies: 6
Views: 1313

Re: Machining single side material

Plam is Plastic laminated. We do a lot of this. For example, Formica 7197 on one side and white backing on the other side (for the Inside of cabinet). We do everything we can to avoid flip parts !! I think the main goal for "single side" option should be to indicate to the cnc operator wic...
by DanFecteau
Sat, Jan 26 2019, 1:02PM
Forum: eCabinet Systems Software
Topic: Machining single side material
Replies: 6
Views: 1313

Machining single side material

I'd like to know how other people proceed when they have to machine single side materials like plam on one side and backing on the other side or for example birch plywood wich Always has a "A side" and a "B side" ? I thought that the "single side" option was created for...
by DanFecteau
Wed, Nov 21 2018, 1:21PM
Forum: Thermwood 3-Axis Machinery
Topic: Laminate and melamin chipping
Replies: 1
Views: 904

Laminate and melamin chipping

Hello, everytime I machine plam or melamine 1'' thick or plus, I get a chip at the Bottom where the tool gets throught material…..I use up & down with proper tool...Any idea on settings to adjust to improve this ? Why it does not do this with 5/8''' thick material, is ramping setting the problem ?
by DanFecteau
Tue, Mar 13 2018, 1:36PM
Forum: Thermwood 3-Axis Machinery
Topic: Machining plam on 1 1/2'' thick pressboard
Replies: 2
Views: 1619

Machining plam on 1 1/2'' thick pressboard

I'm having bad results (chipping) on outline afert only 4-5 sheets, mostly on top of board. I'm usign Onsrud 60-181Mw at 18 000 rpm and 250-300 feed in 2 passes....Any idea what is the problem ? Is there anyway I could do an outline with variable depth at 1st pass in the same outline ? Oscillating ?...
by DanFecteau
Fri, Jan 26 2018, 2:09PM
Forum: Thermwood 3-Axis Machinery
Topic: Machining plam on 1 1/2'' particle board
Replies: 2
Views: 1363

Machining plam on 1 1/2'' particle board

I have 160 vanities to produce and they are mostly made of 1 1/2'' thick particle board with plastic laminate on both sides. I was wondering what tool do you guys use, feed, rpm, etc.... I've had bad results in the past, only able to cut couple sheets before having bad quality cuts...
by DanFecteau
Tue, Jan 17 2017, 8:07AM
Forum: Thermwood 3-Axis Machinery
Topic: Cut-out instead of pocket
Replies: 13
Views: 4097

Re: Cut-out instead of pocket

Not working even after the upgrade, I'm sending the export by email.
by DanFecteau
Mon, Jan 16 2017, 8:54AM
Forum: Thermwood 3-Axis Machinery
Topic: Cut-out instead of pocket
Replies: 13
Views: 4097

Re: Cut-out instead of pocket

Thanks Brad ! I'll update first !
by DanFecteau
Mon, Jan 16 2017, 8:37AM
Forum: Thermwood 3-Axis Machinery
Topic: Cut-out instead of pocket
Replies: 13
Views: 4097

Re: Cut-out instead of pocket

You need the .cnc ?
by DanFecteau
Mon, Jan 16 2017, 7:38AM
Forum: Thermwood 3-Axis Machinery
Topic: Cut-out instead of pocket
Replies: 13
Views: 4097

Re: Cut-out instead of pocket

No not working with group...no idea where the problem is...
by DanFecteau
Mon, Jan 16 2017, 7:16AM
Forum: Thermwood 3-Axis Machinery
Topic: Cut-out instead of pocket
Replies: 13
Views: 4097

Re: Cut-out instead of pocket

Does not seem to work ! Look at the pictures...

Go to advanced search