Search found 44 matches

by Nick Sollecito
Tue, Apr 28 2015, 10:20AM
Forum: eCabinet Systems Software
Topic: Part editor question/suggestion
Replies: 7
Views: 7354

Re: Part editor question/suggestion

That's great! I knew there had to be a solution I just couldn't figure it out. I do know about the slide pattern.
Thank you. That will save me a lot of time!
Nick
by Nick Sollecito
Tue, Apr 28 2015, 7:03AM
Forum: eCabinet Systems Software
Topic: Part editor question/suggestion
Replies: 7
Views: 7354

Part editor question/suggestion

Is there a way to add holes to a part incrementally in the part editor? For example, it would be helpful when adding holes for slides. After the first hole is located it would be much easier to move over to the next location by the incremental dimension rather than calculating the absolute location....
by Nick Sollecito
Thu, Jan 23 2014, 12:18PM
Forum: eCabinet Systems Software
Topic: Book matching in the nest program
Replies: 2
Views: 3392

Re: Book matching in the nest program

I will give it a try and let you know how I make out.
Thanks for the info!
Nick
by Nick Sollecito
Tue, Jan 21 2014, 10:58AM
Forum: eCabinet Systems Software
Topic: Book matching in the nest program
Replies: 2
Views: 3392

Book matching in the nest program

I am trying to find a way to manipulate parts in a nest so I can book match the grain. Doors drawer faces etc. Is there a way to do this?
Thanks!
Nick
by Nick Sollecito
Thu, Mar 03 2011, 7:52AM
Forum: eCabinet Systems Software
Topic: Failed to create toolpath error
Replies: 12
Views: 9991

Re: Failed to create toolpath error

You deserve at least two goddess' for that! :lol:
by Nick Sollecito
Wed, Mar 02 2011, 2:21PM
Forum: eCabinet Systems Software
Topic: Failed to create toolpath error
Replies: 12
Views: 9991

Re: Failed to create toolpath error

You got to be kidding me! How did you even find it?
No Problem, I can make the slot wider.
Thanks again!
Nick
by Nick Sollecito
Wed, Mar 02 2011, 12:33PM
Forum: eCabinet Systems Software
Topic: Failed to create toolpath error
Replies: 12
Views: 9991

Re: Failed to create toolpath error

Hi Scott,
I tried to attach the export file but it says "the extension CAB is not allowed".
Thanks
Nick
by Nick Sollecito
Tue, Mar 01 2011, 2:32PM
Forum: eCabinet Systems Software
Topic: Failed to create toolpath error
Replies: 12
Views: 9991

Re: Failed to create toolpath error

Hi Josh,
Gave it a try but it didn't work. It has to be something with the tooling because I doubled the size of the pocket and it used the next size tool and I didn't get the error. :wall:
by Nick Sollecito
Tue, Mar 01 2011, 9:54AM
Forum: eCabinet Systems Software
Topic: Failed to create toolpath error
Replies: 12
Views: 9991

Failed to create toolpath error

I created a 3/4" X 48" X 96" panel with (94) 1/8" wide pockets 1/2" deep running the width of the panel. (See attached job file) It will nest in eCabinets but when I nest on the machine I get the error message: "Failed to create toolpath for pocket operation 1" the...
by Nick Sollecito
Fri, Jan 07 2011, 10:18AM
Forum: Customer 3D Files
Topic: Help converting DXF to STL
Replies: 4
Views: 7847

Re: Help converting DXF to STL

I'll play around with it. I just downloaded Accutran and I am not familiar with it. On the files that you sent me... I unzipped the files and put all the stl files in the Appliance/Refrigerator folder. I also put the jpg in the same folder. I cannot see the wine refrigerator in the refrigerator list...
by Nick Sollecito
Fri, Jan 07 2011, 7:37AM
Forum: Customer 3D Files
Topic: Help converting DXF to STL
Replies: 4
Views: 7847

Re: Help converting DXF to STL

Hi George,
Thank you for doing the conversion. Much appreciated. I would really like to know how you were able to find the parts of the file to convert. When I opened the file in Accutran I could only see the Viking nameplate.
Thanks
Nick
by Nick Sollecito
Thu, Jan 06 2011, 11:18AM
Forum: Customer 3D Files
Topic: Help converting DXF to STL
Replies: 4
Views: 7847

Help converting DXF to STL

Hi Could someone help with converting a DXF to STL? I downloaded Accutran and loaded in the following 3d dxf file for a viking refrigerator but when it loads in Accutran it only shows the nameplate. When I look at the file with a solidworks dxf viewer it shows all of the views for the refrigerator. ...
by Nick Sollecito
Fri, Dec 10 2010, 10:36AM
Forum: eCabinet Systems Software
Topic: Lost the appliance button
Replies: 4
Views: 4577

Re: Lost the appliance button

I think that's it.
The mind is a terrible thing to waste. :oops:
Thanks!
by Nick Sollecito
Fri, Dec 10 2010, 10:02AM
Forum: eCabinet Systems Software
Topic: Lost the appliance button
Replies: 4
Views: 4577

Re: Lost the appliance button

Ah yes, it is there in the custom layout section. In the past I thought I had added appliances into an assembly when I was in the cabinet editor but I guess I did it in custom layout.
Thanks for setting me straight.
by Nick Sollecito
Fri, Dec 10 2010, 9:40AM
Forum: eCabinet Systems Software
Topic: Lost the appliance button
Replies: 4
Views: 4577

Lost the appliance button

I lost the Appliance button in the cabinet editor. All the other buttons are there and it is still in the Ecabinets file when I look in Windows Explorer. Any one experience this?
Thanks!
Nick