Search found 266 matches

by Joe Soto
Fri, Apr 19 2019, 8:33AM
Forum: eCabinet Systems Software
Topic: Error message lacking info
Replies: 2
Views: 40

Re: Error message lacking info

Same issue in the change materials in the room area. An error saying a constraint can't be applied and will be removed or a locked opening wont allow the change. No idea as to what part or cabinet. Probably more annoying is when that dialog pops up, it stops working until you hit ok. Sometimes chang...
by Joe Soto
Thu, Feb 07 2019, 2:11PM
Forum: eCabinet Systems Software
Topic: corner cabinet toe kick
Replies: 4
Views: 309

Re: corner cabinet toe kick

Got it, removed left end part editor cuts and reapplied them. All is well. Thanks
by Joe Soto
Thu, Feb 07 2019, 1:38PM
Forum: eCabinet Systems Software
Topic: corner cabinet toe kick
Replies: 4
Views: 309

Re: corner cabinet toe kick

That's the way it came off the router too but I need the toe to be flush with the notch.
by Joe Soto
Wed, Feb 06 2019, 5:23PM
Forum: eCabinet Systems Software
Topic: corner cabinet toe kick
Replies: 4
Views: 309

corner cabinet toe kick

toe kick .jpg I can not figure out why the toe kick notch is 1/4" shorter on this side. I've used this same cabinet for several years without a problem. I cut this cabinet today and both ends cut like this but Ecabs only shows it on the left. The only recent changes were I added some screw hol...
by Joe Soto
Mon, Oct 08 2018, 9:50AM
Forum: eCabinet Systems Software
Topic: Carvings
Replies: 1
Views: 740

Re: Carvings

Here you go Carmen.
http://www.ecabinetsystems.com/ecabinet ... ograms.htm
There is an HSF file, which can be loaded into eCabinets.
Joe
by Joe Soto
Thu, Aug 02 2018, 10:03AM
Forum: Thermwood 3-Axis Machinery
Topic: Manual Nesting issues, etc...
Replies: 8
Views: 2005

Re: Manual Nesting issues, etc...

Same problem here, mine stalls when I click the calculate off-fall button. Even if I don't move anything in the nest.
by Joe Soto
Tue, Jul 24 2018, 10:06AM
Forum: eCabinet Systems Software
Topic: Can't have 2 faceframe thickness materials?
Replies: 15
Views: 3470

Re: Can't have 2 faceframe thickness materials?

Try this work around. Design your cabinet with the thick stiles, delete top bottom and mid rails. On page 2 of face frames change add mid rail to your thinner thickness material and add them to the cabinet to replace the rails you deleted.
2 thickness frame.JPG
2 thickness frame.JPG (12.54 KiB) Viewed 2692 times
by Joe Soto
Tue, Apr 10 2018, 11:17AM
Forum: eCabinet Systems Software
Topic: Diagonal corner cabinet problems
Replies: 2
Views: 1009

Re: Diagonal corner cabinet problems

Not sure why but change if you change your blind dado placement from 2.19" to 2.25" it will fix your cabinet.
by Joe Soto
Thu, Oct 26 2017, 9:55AM
Forum: eCabinet Systems Software
Topic: Is there a way to make doors with sheet stock panels ?
Replies: 8
Views: 2555

Re: Is there a way to make doors with sheet stock panels ?

I believe Andy is wanting a 5pc. flat panel door with hardwood rails and plywood for the panel.
by Joe Soto
Mon, Nov 09 2015, 3:53PM
Forum: Thermwood 3-Axis Machinery
Topic: Stuck on scrap part recovery
Replies: 2
Views: 3446

Re: Stuck on scrap part recovery

Thanks Larry I cant reproduce the add issue today either but did several times Friday. Reloading the software today may have corrected it.
Clicking the OK is how I am leaving the Load screen, still keeps scrap part recovery on unless I clear all.
by Joe Soto
Fri, Nov 06 2015, 8:55AM
Forum: Thermwood 3-Axis Machinery
Topic: Stuck on scrap part recovery
Replies: 2
Views: 3446

Stuck on scrap part recovery

Control Nesting v5.88 If I load a .twd or .dxf and check the scrap part recovery box then nest everything is fine. Go back to load screen box is unchecked but it still nest the parts separately. Also if I add another .twd it only nest the first one loaded. Turning off the parts on the first and nest...
by Joe Soto
Thu, Nov 05 2015, 2:01PM
Forum: Thermwood 3-Axis Machinery
Topic: Just purchased a 2004 Thermwood CS40
Replies: 3
Views: 4525

Re: Just purchased a 2004 Thermwood CS40

Hey Andy, I have '06 CS40 with I'm guessing is the same blower. It works really well. I cut a lot of 1/2" Columbia prefinished at 600ipm with a 3/8'' 2 flute compression bit. I have my double pass set at 8" max part size and 4" min for leave skin. I could probably go less if I set the...
by Joe Soto
Thu, Nov 06 2014, 5:16PM
Forum: eCabinet Systems Software
Topic: Nesting Material issues
Replies: 4
Views: 1707

Re: Nesting Material issues

Hi Tim, Looks like your material is .49" wide
by Joe Soto
Tue, May 14 2013, 1:37PM
Forum: Thermwood 3-Axis Machinery
Topic: EMER STOP
Replies: 6
Views: 3445

Re: EMER STOP

I had the same problem last year. Try to clean the retention knob on the tool holder or change to a different tool holder.
Joe
by Joe Soto
Mon, Oct 08 2012, 8:50AM
Forum: eCabinet Systems Software
Topic: Thermwood Adds "Personal Pause Button" to YouBuild
Replies: 6
Views: 3107

Re: Thermwood Adds "Personal Pause Button" to YouBuild

Kerry, From what I understand its part of the You Build upgrade. I believe it's designed to save production time by getting the operator away from the controller to do other jobs but still be in control. There is a lot of interest in You Build here. I am mostly a cabinet and part cutting shop so I d...

Go to advanced search