Search found 82 matches

by Jeff Norris
Mon, Jul 06 2009, 7:42PM
Forum: Lounge
Topic: For sale Thermwood LP1 Cutoff saw
Replies: 0
Views: 2977

For sale Thermwood LP1 Cutoff saw

hey guys, i have a thermwood LP1 length processor cut off saw for sale, its kind of like a tigerstop, it will take files from ecabinets. they did not make too many of them, this one has very little use as we have a tigerstop and purchased this as a package with some other equipment. send me PM if in...
by Jeff Norris
Wed, Jun 06 2007, 1:25PM
Forum: eCabinet Systems Software
Topic: Success with the program
Replies: 28
Views: 20979

will some advice, just keep it simple until you understand the complexities of the system, do not try to use all of the various functions in a grand design and then manufacture it under a short deadline. take your time and when you explore new functions be careful and do not expect everything to go ...
by Jeff Norris
Sat, Jun 02 2007, 12:41PM
Forum: eCabinet Systems Software
Topic: Success with the program
Replies: 28
Views: 20979

some may notice that I don’t post here much anymore, this is because of the many problems described above, I started with ecabs on version 1.5 and own three thermwood machines, I had high hopes for ecabs, but found I could not continue with the consistent bugs especially related to the blind dado, s...
by Jeff Norris
Wed, Apr 11 2007, 2:15PM
Forum: eCabinet Systems Software
Topic: Cycle time Info on 45-510
Replies: 7
Views: 6553

everyone gets excited about a dramatic increase in productivity but i would point out that initially you may have a decrease in productivity untill you get up and going, some other factors to consider in regards to ROI are not so quantifiable, increased quality, increased capabilities, higher safety...
by Jeff Norris
Tue, Apr 10 2007, 8:01PM
Forum: eCabinet Systems Software
Topic: Hardware Hole Associations Disappear !
Replies: 5
Views: 5331

welcome to ecabinet systems
by Jeff Norris
Tue, Apr 10 2007, 7:51PM
Forum: eCabinet Systems Software
Topic: Cycle time Info on 45-510
Replies: 7
Views: 6553

oops double post
by Jeff Norris
Tue, Apr 10 2007, 7:49PM
Forum: eCabinet Systems Software
Topic: Cycle time Info on 45-510
Replies: 7
Views: 6553

be careful in your expectations, i have cut nearly 150 sheets in a day, and i have spent a day programming two cabinets and another day cutting two sheets, if you build similar cabinets all of the time it is easier to predict the results, but if you are like me and build super custom all of the time...
by Jeff Norris
Tue, Apr 10 2007, 7:44PM
Forum: eCabinet Systems Software
Topic: Is there an affordable laptop to run ecabinets?
Replies: 21
Views: 17282

asus makes some super notebooks for a great price,
by Jeff Norris
Tue, Apr 10 2007, 7:33PM
Forum: eCabinet Systems Software
Topic: Panel Optimizer
Replies: 2
Views: 3969

brent change your nesting settings to \"cut line\" and ecabinets will optimize for a table saw
by Jeff Norris
Sun, Sep 24 2006, 2:30PM
Forum: Thermwood 3-Axis Machinery
Topic: dovetail drawers and wasteboard
Replies: 1
Views: 2976

actually i ignored the proper place to put my waste board thickness.
by Jeff Norris
Sun, Sep 24 2006, 10:36AM
Forum: Thermwood 3-Axis Machinery
Topic: dovetail drawers and wasteboard
Replies: 1
Views: 2976

dovetail drawers and wasteboard

cutting a dovetail drawer yesterday and rolling nest ignored my wastboard thickness and cut thru to the spoil board. why would this happen?
by Jeff Norris
Sun, Sep 10 2006, 10:29AM
Forum: Thermwood 3-Axis Machinery
Topic: this is so old
Replies: 4
Views: 6333

this is no graphic issue just ecabinets
by Jeff Norris
Sat, Sep 09 2006, 3:43PM
Forum: Thermwood 3-Axis Machinery
Topic: this is so old
Replies: 4
Views: 6333

spend another hour of my life, delete all the edge banding and now it will nest. this is great!
by Jeff Norris
Sat, Sep 09 2006, 1:37PM
Forum: Thermwood 3-Axis Machinery
Topic: this is so old
Replies: 4
Views: 6333

more
by Jeff Norris
Sat, Sep 09 2006, 1:36PM
Forum: Thermwood 3-Axis Machinery
Topic: this is so old
Replies: 4
Views: 6333

this is so old

wonder what would happen if i ran this program