Search found 82 matches
- Mon, Jul 06 2009, 7:42PM
- Forum: Lounge
- Topic: For sale Thermwood LP1 Cutoff saw
- Replies: 0
- Views: 3011
For sale Thermwood LP1 Cutoff saw
hey guys, i have a thermwood LP1 length processor cut off saw for sale, its kind of like a tigerstop, it will take files from ecabinets. they did not make too many of them, this one has very little use as we have a tigerstop and purchased this as a package with some other equipment. send me PM if in...
- Wed, Jun 06 2007, 1:25PM
- Forum: eCabinet Systems Software
- Topic: Success with the program
- Replies: 28
- Views: 21213
will some advice, just keep it simple until you understand the complexities of the system, do not try to use all of the various functions in a grand design and then manufacture it under a short deadline. take your time and when you explore new functions be careful and do not expect everything to go ...
- Sat, Jun 02 2007, 12:41PM
- Forum: eCabinet Systems Software
- Topic: Success with the program
- Replies: 28
- Views: 21213
some may notice that I don’t post here much anymore, this is because of the many problems described above, I started with ecabs on version 1.5 and own three thermwood machines, I had high hopes for ecabs, but found I could not continue with the consistent bugs especially related to the blind dado, s...
- Wed, Apr 11 2007, 2:15PM
- Forum: eCabinet Systems Software
- Topic: Cycle time Info on 45-510
- Replies: 7
- Views: 6585
everyone gets excited about a dramatic increase in productivity but i would point out that initially you may have a decrease in productivity untill you get up and going, some other factors to consider in regards to ROI are not so quantifiable, increased quality, increased capabilities, higher safety...
- Tue, Apr 10 2007, 8:01PM
- Forum: eCabinet Systems Software
- Topic: Hardware Hole Associations Disappear !
- Replies: 5
- Views: 5357
- Tue, Apr 10 2007, 7:51PM
- Forum: eCabinet Systems Software
- Topic: Cycle time Info on 45-510
- Replies: 7
- Views: 6585
- Tue, Apr 10 2007, 7:49PM
- Forum: eCabinet Systems Software
- Topic: Cycle time Info on 45-510
- Replies: 7
- Views: 6585
be careful in your expectations, i have cut nearly 150 sheets in a day, and i have spent a day programming two cabinets and another day cutting two sheets, if you build similar cabinets all of the time it is easier to predict the results, but if you are like me and build super custom all of the time...
- Tue, Apr 10 2007, 7:44PM
- Forum: eCabinet Systems Software
- Topic: Is there an affordable laptop to run ecabinets?
- Replies: 21
- Views: 17378
- Tue, Apr 10 2007, 7:33PM
- Forum: eCabinet Systems Software
- Topic: Panel Optimizer
- Replies: 2
- Views: 3985
- Sun, Sep 24 2006, 2:30PM
- Forum: Thermwood 3-Axis Machinery
- Topic: dovetail drawers and wasteboard
- Replies: 1
- Views: 3010
- Sun, Sep 24 2006, 10:36AM
- Forum: Thermwood 3-Axis Machinery
- Topic: dovetail drawers and wasteboard
- Replies: 1
- Views: 3010
dovetail drawers and wasteboard
cutting a dovetail drawer yesterday and rolling nest ignored my wastboard thickness and cut thru to the spoil board. why would this happen?
- Sun, Sep 10 2006, 10:29AM
- Forum: Thermwood 3-Axis Machinery
- Topic: this is so old
- Replies: 4
- Views: 6411
- Sat, Sep 09 2006, 3:43PM
- Forum: Thermwood 3-Axis Machinery
- Topic: this is so old
- Replies: 4
- Views: 6411
- Sat, Sep 09 2006, 1:37PM
- Forum: Thermwood 3-Axis Machinery
- Topic: this is so old
- Replies: 4
- Views: 6411
- Sat, Sep 09 2006, 1:36PM
- Forum: Thermwood 3-Axis Machinery
- Topic: this is so old
- Replies: 4
- Views: 6411
this is so old
wonder what would happen if i ran this program