Search found 43 matches

by Chris Say
Tue, Apr 03 2007, 4:08PM
Forum: eCabinet Systems Software
Topic: More transparencies
Replies: 13
Views: 2394

Kerry I found the wood technology pull you described. The pull shows up on the cabinet but there are no holes on the door when I nest it. I do not want the pull to show up in the renderings, I just want the holes so the router can machine them. After double checking the associate hardware option the...
by Chris Say
Fri, Mar 30 2007, 10:31AM
Forum: eCabinet Systems Software
Topic: More transparencies
Replies: 13
Views: 2394

As far as I know I can't associate a hole pattern to the particular pull we use. It is the AM-BP76312-26D 4\" wire pull in the Amerock catalogue. I have made a handle pattern and tried to associate it to the pull with no luck. I have also tried to associate a hole pattern to the pull in the def...
by Chris Say
Fri, Mar 30 2007, 10:28AM
Forum: eCabinet Systems Software
Topic: More transparencies
Replies: 13
Views: 2394

As far as I know I can't associate a hole pattern to the particular pull we use. It is the AM-BP76312-26D 4\" wire pull in the Amerock catalogue. I have made a handle pattern and tried to associate it to the pull with no luck. I have also tried to associate a hole pattern to the pull in the def...
by Chris Say
Thu, Mar 29 2007, 12:22PM
Forum: eCabinet Systems Software
Topic: More transparencies
Replies: 13
Views: 2394

You asked a good question. The reason why I go to part editor is to put the handle hole locations on the front or door. I then go to constraint manager and put constraints on the hole locations so when I go to re-size the cabinet the handle location stays in the same relation to the location I origi...
by Chris Say
Wed, Mar 28 2007, 10:19AM
Forum: eCabinet Systems Software
Topic: More transparencies
Replies: 13
Views: 2394

More transparencies

I am still getting wierd results with my doors after 5.1 bld 2. I read that this was fixed in this build. I have a couple scenarios where transparent doors are created. Most of the problems occur with drawer banks. I notice that after I add a door then take it into part editor to make the handle pat...
by Chris Say
Mon, Mar 12 2007, 11:13AM
Forum: eCabinet Systems Software
Topic: Transparent Doors Again
Replies: 5
Views: 925

I noticed the same things you did when I was placing in custom layout. It was frustrating because when they are transparent it causes a lot problems at the machine. The similarities between our doors are slab doors, banding (my thickness is 1/32\"), part editor cuts, and constraints. I hope thi...
by Chris Say
Thu, Mar 08 2007, 3:15PM
Forum: eCabinet Systems Software
Topic: Transparent Doors Again
Replies: 5
Views: 925

I have found a way to get the doors to appear again. If I look at the cabinet from the side view the banding can be selected. I can take the part into part editor again to put the handle holes in. After that go back into the main screen and the fronts appear. I hope this might help to figure out the...
by Chris Say
Thu, Mar 08 2007, 12:30PM
Forum: eCabinet Systems Software
Topic: Transparent Doors Again
Replies: 5
Views: 925

Transparent Doors Again

I still have problems with doors. It seems when I have a lot of part editor cuts in a cabinet especially on the doors resizing or regenerating the cabinet will cause the doors to become transparent. The only thing visible is the edgebanding. I will attach the job file. They are in the batch. Take th...
by Chris Say
Tue, Feb 20 2007, 11:01AM
Forum: eCabinet Systems Software
Topic: Lost machining
Replies: 10
Views: 1437

Hey guys, thanks for pursuing my MDF door concerns. I made the door out of a cabinet part hoping that the part would be stretchable. I found out quickly that is not possible even with constraint manager. I am trying to find the easiest and fastest way to make a MDF door. We have the profile tool bit...
by Chris Say
Thu, Feb 15 2007, 7:11PM
Forum: eCabinet Systems Software
Topic: Lost machining
Replies: 10
Views: 1437

Hey thanks Brian. That is the advice I got from thermwood just to draw the door. In doing that I was successful in getting the route to show up on the part but now when I try to nest it the part shows no machining on the computer or out at the machine. How did you get your arched doors to nest? How ...
by Chris Say
Tue, Feb 13 2007, 1:05PM
Forum: Thermwood 3-Axis Machinery
Topic: Machine won't nest
Replies: 4
Views: 710

We updated to 5.15 and now we are able to nest jobs. Any idea why the error happened? If you still can't email to chris or joe @lamwks.com please call. (480) 892-6656
by Chris Say
Tue, Feb 13 2007, 11:10AM
Forum: eCabinet Systems Software
Topic: Lost machining
Replies: 10
Views: 1437

We are running SuperControl Version 6.1.2.4
and
Control Nest 5.11 (with Profile Modeler)
by Chris Say
Tue, Feb 13 2007, 10:36AM
Forum: eCabinet Systems Software
Topic: Lost machining
Replies: 10
Views: 1437

Lost machining

I have created an arched MDF door. The part shows the routes correctly in editor but when it is nested the tool paths are not there. The same thing happens at the machine. I had trouble even designing this door because of an \"internal algorithmic\" error. Why won't the nest recognize the ...
by Chris Say
Tue, Feb 13 2007, 10:31AM
Forum: Thermwood 3-Axis Machinery
Topic: Machine won't nest
Replies: 4
Views: 710

Machine won't nest

After trying to add a TWD file into the machine and then nesting it an error \"Cannot find nestlib. Exiting\" comes up. I have tried shutting down the machine and restarting it, creating another job with no luck. What does this error mean?
by Chris Say
Tue, Jan 30 2007, 3:56PM
Forum: eCabinet Systems Software
Topic: Part Editor Crash
Replies: 5
Views: 1043

I am completely at a loss as to why I have lines in different planes. What you said makes sense. I never flipped the part to the back and I entered specific coordinates for every line. Just something new I stumbled upon, I guess.

Go to advanced search