Search found 11 matches
- Thu, Aug 05 2010, 4:29PM
- Forum: eCabinet Systems Software
- Topic: change drawer slides
- Replies: 2
- Views: 2947
change drawer slides
Is this possible? My search didn't find anything. My job is all designed and specified. But I need to change all of the drawer slides from simple side mounts - 1/2" clearance - to soft-close undermounts with 5/8" clearance. In other words, I need to change the sizes - ie cutlist - for all ...
- Fri, Aug 03 2007, 9:15AM
- Forum: eCabinet Systems Software
- Topic: outsourcing drawers
- Replies: 0
- Views: 2434
outsourcing drawers
Is there a way to price drawer boxes from an alternate source? I have a good local source and don't need or want the list of drawer parts. I would like to be able to use the square foot pricing from my supplier.
Can it be done? If not, any suggestions?
Thanks, Rick Fulgham
Can it be done? If not, any suggestions?
Thanks, Rick Fulgham
- Tue, Jul 31 2007, 8:24AM
- Forum: eCabinet Systems Software
- Topic: diagonal corner cabinet
- Replies: 1
- Views: 2265
Ok you can scratch that request. My first attempt at searching the archives was unsuccessful but the second try worked! The solution was to take the sides off of a diagonal cabinet. It even puts shelf holes in the back for adjustable shelves! I lost the answer when I jumped here, but thanks to whome...
- Tue, Jul 31 2007, 7:47AM
- Forum: eCabinet Systems Software
- Topic: diagonal corner cabinet
- Replies: 1
- Views: 2265
diagonal corner cabinet
I need to build a small corner cabinet w/shelves on top. Just a small triangle - 2 sides - or a side and back, depending on your point of view.
Is there as easy way to do this? or do I have to cut up parts and piece them back together?
Any help would be appreciated.
Rick Fulgham
Is there as easy way to do this? or do I have to cut up parts and piece them back together?
Any help would be appreciated.
Rick Fulgham
- Tue, Jul 03 2007, 4:46PM
- Forum: eCabinet Systems Software
- Topic: eCabinets is dying!
- Replies: 7
- Views: 6069
eCabinets is dying!
I am presently a very unhappy camper. When I tried to save my job - which I had of course failed to save all along - after spending half the day on, nothing is happening! Task manager says eCabinets is using 99% of the CPU but is not responding. I really don't want to lose all of this work. Is it re...
- Tue, Mar 20 2007, 4:53PM
- Forum: eCabinet Systems Software
- Topic: new install and crash
- Replies: 5
- Views: 4265
- Tue, Mar 20 2007, 1:00PM
- Forum: eCabinet Systems Software
- Topic: new install and crash
- Replies: 5
- Views: 4265
new install and crash
HELP! I'm going crazy. I just got a new computer to try to make eCabinets run faster. I copied all of the files onto the new hard drive and it wouldn't run. So I reinstalled the software from the V5 CD, then ran the 5.1 build 2 update. The program runs and will open one of my batch cabinet files but...
- Sun, Mar 11 2007, 3:53PM
- Forum: eCabinet Systems Software
- Topic: re-sizing errors
- Replies: 9
- Views: 6669
- Sun, Mar 11 2007, 3:48PM
- Forum: eCabinet Systems Software
- Topic: re-sizing errors
- Replies: 9
- Views: 6669
Oops! I typed in a reply earlier but didn't send it, got delayed, and the system kicked me off. Guess I'll try again. I make a wooden T-mold to match my cabinets. Typically it's 13/16 wide with a 1/4 x 7/16 tongue. That way I get a solid edge that I can make wider for scribes, bottom light rail, ext...
- Sat, Mar 10 2007, 12:15PM
- Forum: eCabinet Systems Software
- Topic: re-sizing errors
- Replies: 9
- Views: 6669
re-sizing errors
I use a T-mold for my frameless cabinets that eCabinets sees as a face frame. When I change the width of a side stile to allow for scribe, the doors and drawers don't resize properly. My only fix has been to delete and reinstall the doors and drawers - too much time. To change the size of the stile,...
- Sun, Feb 18 2007, 1:37AM
- Forum: eCabinet Systems Software
- Topic: flat panel doors w/center stile
- Replies: 4
- Views: 4744
flat panel doors w/center stile
I'm still new to all this . . . I need to build in house some simple \"Shaker\" style doors with flat plywood panels. The wider doors need an extra center stile (thus 2 equal panels). I'm pretty sure Conastoga actually makes a door like this, but it's not in the standard directory. Can it ...