Search found 17 matches

by Greg Haw
Mon, Feb 25 2013, 7:37PM
Forum: eCabinet Systems Software
Topic: Object Snap
Replies: 1
Views: 490

Object Snap

Object snap does not seem to work. Is the cross hairs not suposed to snap to the end of a line or corner of part in part editor if object snap is on? Trying to make a closed conture seems almost impossible for me. I do use the extend and trim controls. But the cross hairs don't seem to snap to anyth...
by Greg Haw
Tue, Jul 31 2012, 9:01AM
Forum: eCabinet Systems Software
Topic: Small Shape Manager
Replies: 1
Views: 576

Small Shape Manager

The work space in Shape Manager only covers about 2/3 of my monitor. Is there a way to expand it?
by Greg Haw
Tue, Jul 31 2012, 8:45AM
Forum: Design Sharing
Topic: Making angle cuts
Replies: 6
Views: 7553

Re: Making angle cuts

Thanks Mark exactly what I was looking for.
by Greg Haw
Tue, Jul 31 2012, 2:12AM
Forum: Design Sharing
Topic: Making angle cuts
Replies: 6
Views: 7553

Re: Making angle cuts

Ok I attached thew cabinet in a jpeg so you can see I hope what I am doing. What I am asking is,How do make the Profile cut and the Part Editor cuts exactly 15 degrees or make any certain angle for that matter. 45 degrees you can make a square then bisect the corners. But say you want. 43 degrees, o...
by Greg Haw
Mon, Jul 30 2012, 12:24AM
Forum: Design Sharing
Topic: Making angle cuts
Replies: 6
Views: 7553

Making angle cuts

I am trying to make a cabinet that has one side angled at 15 degrees. I am using one cabine with 3 sides cutting the ends of the top and deck at 15 degrees in part editor,or at least trying. Is thgere away to make a pricise 15 degree cut? Closest I have come is 14 degrees. Also need to bevel the 4th...
by Greg Haw
Fri, Jul 20 2012, 9:17PM
Forum: eCabinet Systems Software
Topic: Drawer box finger cut out.
Replies: 3
Views: 1041

Re: Drawer box finger cut out.

drawer unit.hsf
(2.5 MiB) Downloaded 73 times
Ok took me awhile to find where the files are stored. Xp was so much easier. Well since it don't let me install the drawer with Part Editor cuts I am not sure if this helps. But Thanks Greg!
by Greg Haw
Thu, Jul 19 2012, 8:03PM
Forum: eCabinet Systems Software
Topic: Drawer box finger cut out.
Replies: 3
Views: 1041

Drawer box finger cut out.

Been trying to make a finger pull cut out in a drawer box front. Used a rectangle and a half circle on either side of it in Partr Editor to make the cut out. When I try to add the drawer box to cabinet I get a message that says "Drawer box cannot be regenerated. Press Yes to remove part editer ...
by Greg Haw
Thu, Jun 21 2012, 11:53PM
Forum: eCabinet Systems Software
Topic: Build 8 install problems
Replies: 5
Views: 902

Re: Build 8 install problems

Yes it did say that!
by Greg Haw
Thu, Jun 21 2012, 7:57PM
Forum: eCabinet Systems Software
Topic: Build 8 install problems
Replies: 5
Views: 902

Re: Build 8 install problems

Well I did as posted and got the command prompt . However, it still did not eliminate the error box stated at the start of this thread
by Greg Haw
Thu, Jun 21 2012, 12:54AM
Forum: eCabinet Systems Software
Topic: Build 8 install problems
Replies: 5
Views: 902

Build 8 install problems

Bought new computer and installed e cabinets. I am running windows 7. It took more ever to get it to load but thanks to this forum I got it. But last problem when I start it I get this message."The Hardware Database failed to update properly. Please try to run the install again and select the r...
by Greg Haw
Wed, Dec 03 2008, 7:58PM
Forum: eCabinet Systems Software
Topic: Panel front.
Replies: 16
Views: 1590

Re: Panel front.

Well ok , Like I said I am just learning the software and don't fully understand much of what was said. I do thank you all for the replies and education. I am just going through old jobs and redoing them in ecabinets to learn the software. If my drafting skills were better I think I would stick with...
by Greg Haw
Tue, Dec 02 2008, 4:42PM
Forum: eCabinet Systems Software
Topic: Panel front.
Replies: 16
Views: 1590

Re: Panel front.

Yes that's what I am trying to do
by Greg Haw
Tue, Dec 02 2008, 1:35PM
Forum: eCabinet Systems Software
Topic: Panel front.
Replies: 16
Views: 1590

Panel front.

Trying to design a cabinet with no doors on the front just 4 panels. Is there a way to do this? I am just learning the software Just so you know. I tried overlapping door to get rid of the extra style. That didn't work to well. Any other ideas?
by Greg Haw
Tue, Nov 04 2008, 12:51PM
Forum: eCabinet Systems Software
Topic: prolblem loading
Replies: 7
Views: 888

Re: prolblem loading

NO I am running windows XP
by Greg Haw
Mon, Nov 03 2008, 8:49PM
Forum: eCabinet Systems Software
Topic: prolblem loading
Replies: 7
Views: 888

Re: prolblem loading

Ok, I got the reset utility confused with the update. I did download the update and was even able to install it. But still cannot install the disk. I tried the uninstall utility from control panel and I get the same error message I get when I try to install. I tried from the disk to remove the softw...

Go to advanced search