Search found 295 matches

by Rob Davis
Tue, Jun 11 2019, 9:13AM
Forum: Thermwood 3-Axis Machinery
Topic: Cutting into adjacent parts
Replies: 6
Views: 77

Re: Cutting into adjacent parts

Thanks Thomas adn Troy. We've cut angled parts before without his issue but never a whole set of them all together.
We'll likely try the radius end first so we don't add extra space between every part in nest.
:beer:
by Rob Davis
Mon, Jun 10 2019, 1:06PM
Forum: Thermwood 3-Axis Machinery
Topic: Cutting into adjacent parts
Replies: 6
Views: 77

Cutting into adjacent parts

I tried to search forum for answer but couldn't find a thread.
We ran these in eCabinets and nested at machine but we are\getting the tools running into adjacent parts. Since nested on Rolling Nest, any suggestions?
by Rob Davis
Thu, Dec 13 2018, 4:32PM
Forum: Lounge
Topic: Holiday Deer
Replies: 5
Views: 1888

Re: Holiday Deer

Brad, If interested, here is the 2 deer version with 4 antlers, one set with minor modification and set up for 0.735 material. Thanks for your assistance in retrieving this oldie but goodie project! If you want a MasterCam version of this as a .nc file, just ask.
by Rob Davis
Tue, Dec 11 2018, 5:33PM
Forum: Lounge
Topic: Holiday Deer
Replies: 5
Views: 1888

Re: Holiday Deer

No apologies necessary. Yours are nicer than the ones we made and more stable (pun intended). I'm stealing yours for this run.
We are making out of 3/4" PVC Foam for weatherproof and no need to paint as white already. Will post pic if successful.
Thx again!
by Rob Davis
Tue, Dec 11 2018, 3:47PM
Forum: Lounge
Topic: Holiday Deer
Replies: 5
Views: 1888

Re: Holiday Deer

Brad, THANKS!!
Actually these are different than the ones we stole originally if you notice legs are different, antlers different, etc.
Merry Christmas!
by Rob Davis
Tue, Dec 11 2018, 1:53PM
Forum: Lounge
Topic: Holiday Deer
Replies: 5
Views: 1888

Holiday Deer

Probably about 10 years ago, somewhere on this forum, someone posted a "Holiday Deer" file that made two deer cutouts per 4x8 sheet. We cut some (pic attached) but over years and upgrades and whatever we can't find file. Does anyone still have it??? I've searched the forums for "deer&...
by Rob Davis
Thu, Sep 27 2018, 2:31PM
Forum: Thermwood 3-Axis Machinery
Topic: Waste Baord issues
Replies: 4
Views: 1264

Re: Waste Baord issues

Thanks all. We're working on it.
by Rob Davis
Wed, Sep 26 2018, 3:48PM
Forum: Thermwood 3-Axis Machinery
Topic: Waste Baord issues
Replies: 4
Views: 1264

Waste Baord issues

Apparently we have done something to make our machine think our waste board is 0.060" thicker than it actually is. So everything is not deep enough. We are faking the machine by entering a waste board into the "machine variables" table in drop down menu. How do we fix this mess we've ...
by Rob Davis
Fri, Jun 29 2018, 4:12PM
Forum: Thermwood 3-Axis Machinery
Topic: Y axis Out of bounds
Replies: 12
Views: 3424

Re: Y axis Out of bounds

All, thanks for the feedback. So you know, this issue was a tool comp issue in the program. Apparently the automatic tool comp adjustment was not doing something properly. In Mastercam, we can either use the tool diameter actually in the machine or we can hard code the tool diameter before we post t...
by Rob Davis
Wed, Jun 20 2018, 3:17PM
Forum: Thermwood 3-Axis Machinery
Topic: Y axis Out of bounds
Replies: 12
Views: 3424

Re: Y axis Out of bounds

Thomas, ours is older machine and not set like that but we do have a wire chase similar and we will check. However, Thermwood had me turn off tool comp and program runs like a dream, even though we ran it 4" above table. Not in wiring likely.
by Rob Davis
Wed, Jun 20 2018, 12:39PM
Forum: Thermwood 3-Axis Machinery
Topic: Y axis Out of bounds
Replies: 12
Views: 3424

Re: Y axis Out of bounds

Thomas, thanks for the suggestion. In the picture, where did you take it? Are these wires in the spindle head or under the table?
by Rob Davis
Wed, Jun 20 2018, 6:25AM
Forum: Thermwood 3-Axis Machinery
Topic: Y axis Out of bounds
Replies: 12
Views: 3424

Re: Y axis Out of bounds

Tim, Thanks for the reply. It is same spot every time. I actually took chain out of program and it advanced but now hangs on another chain some 50 chains later, same issue. Took that out and advanced another ways through prorgam. I have Thermwood looking at it and sent all the files. I wondered if a...
by Rob Davis
Mon, Jun 18 2018, 1:02PM
Forum: Thermwood 3-Axis Machinery
Topic: Y axis Out of bounds
Replies: 12
Views: 3424

Y axis Out of bounds

Has anybody got any insight into why we could be running along machining a part where there are several of same part on a sheet and all at once we get "Y axis out of bounds"? It is in the middle of the sheet, we get about 60 pcs per sheet and it is the same one every time. It is in the 5th...
by Rob Davis
Wed, Jan 31 2018, 8:03AM
Forum: eCabinet Systems Software
Topic: Temp folder error
Replies: 5
Views: 1783

Re: Temp folder error

Thanks, Tim. I've tried that but no luck. It is strange.
by Rob Davis
Tue, Jan 30 2018, 8:07AM
Forum: eCabinet Systems Software
Topic: Temp folder error
Replies: 5
Views: 1783

Re: Temp folder error

And, I can take twd file to machine and it nests fine.
My next step is to uninstall and re-install

Go to advanced search