Search found 22 matches

by Christopher Stapleton
Mon, Jan 30 2012, 6:58PM
Forum: eCabinet Systems Software
Topic: Registration Code already used
Replies: 2
Views: 852

Re: Registration Codes may not be Shared

Thank you.
Best regards to Jeff.
by Christopher Stapleton
Mon, Jan 30 2012, 4:46PM
Forum: eCabinet Systems Software
Topic: Registration Code already used
Replies: 2
Views: 852

Registration Code already used

Ken, After some time away from the software, I'm trying to intialize andother instance of V5 on a laptop, after I had installed the same license on my desktop. The software error message I receive basically states that I cannot use the code to initialize an instance of the software if its already be...
by Christopher Stapleton
Thu, Jan 11 2007, 10:00AM
Forum: eCabinet Systems Software
Topic: Countertop glitch
Replies: 7
Views: 2111

Mike, Thanks for your continued interest. The bar base unit is an L or J shaped one except that the corener is formed by a standard cabinet alighed 45 dgree to it adjacent cabinets. A corner cabinet could have been used I suppose, but this is not what the customer wanted. The base cabinets are defin...
by Christopher Stapleton
Wed, Jan 10 2007, 1:21PM
Forum: eCabinet Systems Software
Topic: Glass rendering dark
Replies: 11
Views: 3010

Keith,

Thanks much, I'll try to learn something from this, but will not have much time to invest for this project.

Cheers

CPS
by Christopher Stapleton
Wed, Jan 10 2007, 12:42PM
Forum: eCabinet Systems Software
Topic: Countertop glitch
Replies: 7
Views: 2111

Won't this create two tops, one for the toe kick and one for the bar base?

Do I just delete the one I dont want then?

Thx
by Christopher Stapleton
Wed, Jan 10 2007, 10:30AM
Forum: eCabinet Systems Software
Topic: Countertop glitch
Replies: 7
Views: 2111

Prior to seperating the association between the toe kicks and the cabinets...Yes. I selected the 40.75\" altitude and carried on, but it still goes to the toekick or molding edge, I cannot tell which. After the disassociation, I do not get that dialog box. But you can still sort of tell where t...
by Christopher Stapleton
Tue, Jan 09 2007, 5:46PM
Forum: eCabinet Systems Software
Topic: Countertop glitch
Replies: 7
Views: 2111

Countertop glitch

Greetings, I cannot seem to correctly add a countertop (in the standard fashion from the detail room screen) to the the attached bar base aeembly. It appears that the countertop creator will not select one of the corners, and instead wants to select what appears to be the outside edge of the toe kic...
by Christopher Stapleton
Tue, Jan 09 2007, 5:00PM
Forum: eCabinet Systems Software
Topic: drawer box designer
Replies: 7
Views: 1922

Drwaer boxes

Eddie,

Any chance your trying to load a drwaer FRONT?

I'm sad to say that I made this mistake several times.

CPS
by Christopher Stapleton
Tue, Jan 09 2007, 4:58PM
Forum: eCabinet Systems Software
Topic: Glass rendering dark
Replies: 11
Views: 3010

Arched Mullions, muntins

Keith, Am working on a bar and am planning to fabricate or buy out arched mullion doors very similar to those shown in your rendering. I elected not to include thi in my fiorst rpesentaiton as I was unsure how to proceed. You're doing this in the part editor and cutting out apnel or cube then applyi...
by Christopher Stapleton
Tue, Jan 09 2007, 4:47PM
Forum: eCabinet Systems Software
Topic: Line Drawings
Replies: 1
Views: 919

Line Drawing

None that I'm aware of. I too seek amore efective way to make alterations that are easily updated in the line drawings, but I doubt that will be forthcoming any time soon. One very good suggetsion from one of the more experienced (Hall or Epps I think) users was to adopt a pdf generator for line dra...
by Christopher Stapleton
Sat, Jan 06 2007, 3:49PM
Forum: eCabinet Systems Software
Topic: Vanishing Assemblies in Custom Layout
Replies: 4
Views: 1882

Vanishing Assemblies

Here is another attempt after a fresh reboot, defrag, memory optimization, etc.

If it fails, I cannot explain.

Thanks
by Christopher Stapleton
Fri, Jan 05 2007, 7:08PM
Forum: eCabinet Systems Software
Topic: Error Message \"Unable to Open HOOPS data\"
Replies: 7
Views: 2276

Still Stumped

Dan, I do not have this banding stock named Puccio base in my Material Library. I tried unsucessfully to print screen a view of it, save in paint, and add the atachement. How are you capturing your screen images? Notwithstanding, I can see that having board stock with the same name as same as the as...
by Christopher Stapleton
Fri, Jan 05 2007, 6:07PM
Forum: eCabinet Systems Software
Topic: Error Message \"Unable to Open HOOPS data\"
Replies: 7
Views: 2276

Materials Definition

Dan, I confirm the Puccio base as board stock, it is a project specific exisiting base board condition used as a display borad in the assembly. I do not see it anywhere else in my material library. I also confirm the 1/8\" mirror and 3/8\" galss shelf as sheet stock. However, I do not see ...
by Christopher Stapleton
Fri, Jan 05 2007, 5:01PM
Forum: eCabinet Systems Software
Topic: Error Message \"Unable to Open HOOPS data\"
Replies: 7
Views: 2276

Zipped Assembly

I have not worked it out and ended up starting all over.
a couple hours of swaping emails and files w/ T'wood, no word back from them. wlater Scott seems to be focused on the cabinets rather than the assembly.

Grateful for any assitance.
by Christopher Stapleton
Fri, Jan 05 2007, 11:35AM
Forum: eCabinet Systems Software
Topic: Anoterh 'Material Not Found Error'
Replies: 4
Views: 1414

Found the error

A Thermwood team member was polite enough tompoint out that the error was betweent he chair and the keyboard. The problem was likely realted to the fact that the directories \"drawer\" and \"drawer boxes\" are right nest to each other. I loaded a \"drawer\" which OF cou...

Go to advanced search