Search found 132 matches

by Gerry A Brown
Thu, Nov 12 2015, 9:03AM
Forum: Thermwood 3-Axis Machinery
Topic: Cnc is loading jobs slow and slow in general
Replies: 24
Views: 9509

Re: Cnc is loading jobs slow and slow in general

Hi, Some ram needs to be installed in banks. You should consult the mother board manual for that information. If you don't have the manual you can find the mother board model printed on the board then do a internet search for the manual. On my board if I am using 2 slots I need to use the first and ...
by Gerry A Brown
Thu, Nov 05 2015, 8:02AM
Forum: Thermwood 3-Axis Machinery
Topic: fixed table stops
Replies: 5
Views: 3184

Re: fixed table stops

Just wanted to update this. I mounted the stops off the cut path of the router by routing a 4 X 8 sheet off the g901 position left the vacuum running then mounted the stops, measured to the cut sheet and then shimmed to make all the stops an equal distance. I then cut my square off these stops and a...
by Gerry A Brown
Fri, Oct 30 2015, 7:50AM
Forum: Thermwood 3-Axis Machinery
Topic: fixed table stops
Replies: 5
Views: 3184

Re: fixed table stops

Hi Will, Yes those are the stops I am referring to. I have been considering mounting a piece of wood to the stops to raise them as I use 1/2" MDF for my waste board and they are a little short when the sheet is new. This would allow me to mill them to a given dimension off the g901 location and...
by Gerry A Brown
Thu, Oct 29 2015, 6:34PM
Forum: Thermwood 3-Axis Machinery
Topic: fixed table stops
Replies: 5
Views: 3184

Re: fixed table stops

table stops.jpg Hi Will, It was that post that got me thinking about these stops. I have included a pic of the machine that shows the fixed stops. They were mounted with shims behind them against the table to align them to the cutting path of the router. I have been using a fixed fence like the one...
by Gerry A Brown
Tue, Oct 27 2015, 7:45AM
Forum: Thermwood 3-Axis Machinery
Topic: fixed table stops
Replies: 5
Views: 3184

fixed table stops

Hello everyone, We have a 2007 CS45 that we bought used. When we got it it had fixed stops mounted to the table for flip ops. The technician removed these stops when he set up the machine and I would like to reinstall them. Could some one point me at some instructions to reinstall these stops? I am ...
by Gerry A Brown
Sat, Oct 10 2015, 2:12PM
Forum: Thermwood 3-Axis Machinery
Topic: New HD issues
Replies: 1
Views: 2648

Re: New HD issues

Hi Marcell,

You might want to check if the windows partition is marked as active. Sometime when restoring a drive clone the partition is not flagged properly.

Gerry
by Gerry A Brown
Wed, Jun 17 2015, 8:44AM
Forum: eCabinet Systems Software
Topic: Applying a drilling pattern to gable
Replies: 2
Views: 906

Re: Applying a drilling pattern to gable

This has come up a number of times and I think it would be a boon for people who use dowels or confirmats but there seems to be no interest from Thermwood of implementing the option.
by Gerry A Brown
Sat, Jun 06 2015, 10:12PM
Forum: Thermwood 3-Axis Machinery
Topic: CS45 Ram Upgrade
Replies: 8
Views: 3387

Re: CS45 Ram Upgrade

I have encountered the problem Micheal describes. The file would not even load until i removed it from the deep folder structure. That had me baffled for quite some time :wall:

Gerry
by Gerry A Brown
Thu, May 28 2015, 2:27PM
Forum: Thermwood 3-Axis Machinery
Topic: sticky job file
Replies: 9
Views: 3815

Re: sticky job file

Hi Will,

Yes I think it was Brad who helped get that working for us. I did not have a problem with this Post P until I did these "tile" files I think I will look at how Aspire is outputting these as all 4 produced at once.

Thanks,
Gerry
by Gerry A Brown
Thu, May 28 2015, 11:39AM
Forum: Thermwood 3-Axis Machinery
Topic: sticky job file
Replies: 9
Views: 3815

Re: sticky job file

Hi Will, We went to the arcs Post P because the machine was stuttering when cutting small arcs, it did seem to resolve that problem. I think as I recall we input code to slow the feed so not to get the chatter, maybe give the one I posted a try to see how it works for you. It is set up to locate at ...
by Gerry A Brown
Thu, May 28 2015, 9:11AM
Forum: Thermwood 3-Axis Machinery
Topic: sticky job file
Replies: 9
Views: 3815

Re: sticky job file

Hi Will,

No I have never been able to sort this out. I have not run any more of these files so I don't know if it is a one time anomaly or what. The post P we are using is using arcs commands so that could be why the starting code is not the same. I have attached a copy of the Post P .

Thanks,
Gerry
by Gerry A Brown
Sat, May 23 2015, 2:12PM
Forum: Thermwood 3-Axis Machinery
Topic: sticky job file
Replies: 9
Views: 3815

Re: sticky job file

It looks like you can only load one file as the super-control won't allow you to select more than one.
Gerry
by Gerry A Brown
Sat, May 23 2015, 11:32AM
Forum: Thermwood 3-Axis Machinery
Topic: sticky job file
Replies: 9
Views: 3815

Re: sticky job file

Hi Tim,

That is something I have never tried. Don;t know if it will solve this problem but it might be handy I'll give it a try.

Thanks,
Gerry
by Gerry A Brown
Sat, May 23 2015, 9:00AM
Forum: Thermwood 3-Axis Machinery
Topic: sticky job file
Replies: 9
Views: 3815

sticky job file

Hello, I have come up against a rather strange problem. We have four job files produced with Aspire. They are a tiled job with 4 tiles, one file for each tile. Once I load one of these files I can not load another file without restarting the super-control software. If I try to load another file ther...
by Gerry A Brown
Mon, May 04 2015, 8:04PM
Forum: Thermwood 3-Axis Machinery
Topic: 2007 CS45 strange video problem
Replies: 3
Views: 2050

Re: 2007 CS45 strange video problem

Hi,

So I was looking for a PCI video card and found a nice ATI AGP card and thought what the heck I may as well try it..............IT WORKS!!!!
Both the other cards were Nvidia so I don't know if that was the issue but I don't care at this point :lol:

Thanks :beer:

Gerry

Go to advanced search