Search found 11 matches

by Paul Rollins
Thu, Jul 10 2008, 11:02AM
Forum: Thermwood 3-Axis Machinery
Topic: Where are my reindeer?!?
Replies: 4
Views: 853

Re: Where are my reindeer?!?

Thank you for the files. I really appreciate you Thermwoodians and your willingness to go the extra mile for we the people.
by Paul Rollins
Tue, Jul 08 2008, 3:33PM
Forum: Thermwood 3-Axis Machinery
Topic: Where are my reindeer?!?
Replies: 4
Views: 853

Where are my reindeer?!?

Where is my reindeer cut out program?!? Don't these machines come with a reindeer cutout program and a name block program? My machine is running so fast that I decided to start a side business selling Christmas lawn reindeer and name blocks. I just know that with my machine training under my belt I ...
by Paul Rollins
Mon, Jul 07 2008, 6:09AM
Forum: Thermwood 3-Axis Machinery
Topic: Staying at Motel 6
Replies: 1
Views: 467

Re: Staying at Motel 6

There is an Enterprise rent a car in Jasper, Indiana and they should be willing to drive the car to you.

Enterprise Rent-A-Car
3790 N NEWTON ST
JASPER, IN 47546-8017
812-634-6344
by Paul Rollins
Fri, Jul 04 2008, 10:44AM
Forum: Thermwood 3-Axis Machinery
Topic: Help for a new machine owner
Replies: 5
Views: 1061

Re: Help for a new machine owner

Thanks for the help. The machine was running some parts with M4 and some with M3, I don't know why. I edited the program and replaced the M4's with the M3's and the parts have run brilliantly. The label printer had a loose wire inside where it reads for the labels to come through and so I fixed that...
by Paul Rollins
Fri, Jul 04 2008, 5:39AM
Forum: Thermwood 3-Axis Machinery
Topic: Help for a new machine owner
Replies: 5
Views: 1061

Re: Help for a new machine owner

When I put a piece of paper on the tool holder threads, the paper pulls up toward the motor. It is turning clockwise if you look down on the spindle. I think this correct. I know that this is a simple mistake somewhere, I just havent figured it out yet.
by Paul Rollins
Thu, Jul 03 2008, 5:07PM
Forum: Thermwood 3-Axis Machinery
Topic: Help for a new machine owner
Replies: 5
Views: 1061

Re: Help for a new machine owner

1/2 inch compression
S18000
F600
3/4 MDF

These are the numbers

thanks
by Paul Rollins
Thu, Jul 03 2008, 5:06PM
Forum: Thermwood 3-Axis Machinery
Topic: Help for a new machine owner
Replies: 5
Views: 1061

Help for a new machine owner

The machine came in and the electrician connected it the same day. We turned it on to make sure everything worked and found several air line situations that needed to be addressed. We designed and cut a curved shelf panel for a bar cabinet that we needed so we could see the machine run. The technici...
by Paul Rollins
Mon, Jun 09 2008, 10:51AM
Forum: eCabinet Systems Software
Topic: Just returned from Ecab training at Thermwood...
Replies: 0
Views: 564

Just returned from Ecab training at Thermwood...

and if anyone who has not been to the training has any questions on what it was like, I can give you the scoop.
by Paul Rollins
Tue, May 27 2008, 8:28AM
Forum: Thermwood 3-Axis Machinery
Topic: Machine Placement
Replies: 5
Views: 957

Re: Machine Placement

Thank you both for your input. The advice about the pump is much appreciated. I would rather have too much space than not enough. The shop is only 8000 sq ft including offices and finishing and I have to be careful with space.
by Paul Rollins
Fri, May 23 2008, 8:36AM
Forum: Thermwood 3-Axis Machinery
Topic: Machine Placement
Replies: 5
Views: 957

Machine Placement

Can I get some feedback on machine placement in the shop? Where did you place yours and how much clearance around the machine did you use? I am trying to place a 45-510. The machines that I have seen in person are indexed on the right front of the machine. Are the indexing pins movable to the other ...
by Paul Rollins
Fri, May 23 2008, 6:51AM
Forum: eCabinet Systems Software
Topic: Need Input-Over my dead body
Replies: 2
Views: 555

Need Input-Over my dead body

will I be paying my current cabinet software company the @22k they are asking to connect up to a CNC based on the service and support I have received so far. My cabinet shop was 8 employees until the market slowed us down to 3. Now i have more work and I am buying a machine instead of hiring more em...

Go to advanced search