Search found 188 matches

by David Egnoski
Fri, Oct 16 2020, 11:13AM
Forum: eCabinet Systems Software
Topic: Crashing on save
Replies: 3
Views: 1717

Re: Crashing on save

What video card do you have installed on this new computer? The 2GB nVidia Quadro K2200 Graphics Card is the recommended video card.
by David Egnoski
Wed, Apr 15 2020, 4:52PM
Forum: Thermwood 3-Axis Machinery
Topic: "Air cut"
Replies: 5
Views: 3063

Re: "Air cut"

Changing the Z height is the only way I know to do it.
by David Egnoski
Wed, Apr 15 2020, 11:06AM
Forum: Thermwood 3-Axis Machinery
Topic: Problems with a file
Replies: 1
Views: 1812

Re: Problems with a file

Check cabinet and part names for any special characters like ' or / or -.
by David Egnoski
Wed, Apr 08 2020, 11:31AM
Forum: Thermwood 3-Axis Machinery
Topic: Bottom of parts chipping
Replies: 4
Views: 2841

Re: Bottom of parts chipping

I've always used a 3" ramp. I might see a small chip if the part is hanging over the edge of the table, but rarely.
by David Egnoski
Tue, Mar 31 2020, 7:39AM
Forum: Lounge
Topic: What methods do you use to hold down small parts?
Replies: 5
Views: 6062

Re: What methods do you use to hold down small parts?

I've used custom spoilboards with great success. The gasket technique Clint talks about takes time to implement but is very effective for large runs. I've also used custom boards with just 3/16" through holes to direct the vacuum to the part. I've cut literally hundreds of sheets with the board...
by David Egnoski
Mon, Feb 24 2020, 11:51AM
Forum: eCabinet Systems Software
Topic: Feature Change Request
Replies: 5
Views: 3848

Re: Feature Change Request

Donald,

I might be able to help you. I've been doing VB and VBA programming for quite some time. Perhaps you could send me your spreadsheet and I can take a look.
by David Egnoski
Mon, Feb 24 2020, 11:49AM
Forum: eCabinet Systems Software
Topic: Error message lacking info
Replies: 5
Views: 5293

Re: Error message lacking info

Exactly the point of my original post. :wink:
by David Egnoski
Wed, Sep 25 2019, 7:01AM
Forum: eCabinet Systems Software
Topic: Custom Layout
Replies: 5
Views: 4688

Re: Custom Layout

I third this request.
by David Egnoski
Tue, Apr 23 2019, 6:59AM
Forum: eCabinet Systems Software
Topic: Pocket Screw Joinery
Replies: 2
Views: 3013

Re: Pocket Screw Joinery

In Construction Parameters for the part in question look at KD/RTA. Lock Dado, Pocket Screw Placement. Change Bottom to Top as needed to achieve desired placement.


Joinery.jpg
by David Egnoski
Tue, Apr 16 2019, 4:40PM
Forum: Thermwood 3-Axis Machinery
Topic: Measuring brad point drill bit
Replies: 3
Views: 3761

Re: Measuring brad point drill bit

Control Nesting provides the option shown in the attachment. It works well.

Drill Depth.pdf
(190.16 KiB) Downloaded 325 times
by David Egnoski
Tue, Apr 16 2019, 2:28PM
Forum: eCabinet Systems Software
Topic: Error message lacking info
Replies: 5
Views: 5293

Error message lacking info

It would be helpful if this dialog box contained the name of the cabinet with the problem. Any chance to get this added?

Thank you.

Error Message.pdf
(174.94 KiB) Downloaded 350 times
by David Egnoski
Sat, Apr 06 2019, 12:33PM
Forum: eCabinet Systems Software
Topic: Can not open ecabinets
Replies: 5
Views: 3891

Re: Can not open ecabinets

Just fishing here but give this a try. Uninstall eCabinets, then look in C:\ProgramData\Thermwood\eCabinet Systems for any files ending in .mdb or .ldb. If you see any, delete them. Install eCabinets and give it a try.

If the uninstall removes that directory completly, I'm all wet.
by David Egnoski
Tue, Feb 12 2019, 2:24PM
Forum: eCabinet Systems Software
Topic: Sink Drawer Cabinet Construction Suggestions (part 1)
Replies: 9
Views: 5331

Re: Sink Drawer Cabinet Construction Suggestions (part 1)

Are those display drawer fronts display panels or drawer fronts without drawer boxes?
by David Egnoski
Wed, Nov 21 2018, 8:21AM
Forum: Thermwood 3-Axis Machinery
Topic: Layers
Replies: 2
Views: 3562

Re: Layers

Go to the link below and open the Control Nesting Manual. Go to page 93 and you'll find the layer names.

Hope this helps you out.

http://www.thermwood.com/software_manuals_main.htm
by David Egnoski
Sat, Oct 20 2018, 2:46PM
Forum: eCabinet Systems Software
Topic: cross section view
Replies: 5
Views: 4057

Re: cross section view

Thanks Forrest. That's what I ended up doing. Just thought the ability to use the cross section tool would be cool.

Go to advanced search