Search found 243 matches

by tim lucas
Thu, Jun 21 2018, 7:23PM
Forum: eCabinet Systems Software
Topic: Line drawing printing issue
Replies: 2
Views: 45

Re: Line drawing printing issue

LDE has some issues, sometimes I can JPG a drawing and everything is there then next time it wont be. If I restart eCabs it usually works right. I also noticed that if a cabinet or countertop is not assocaited to a wall it wont show in LDE.
by tim lucas
Wed, Jun 20 2018, 5:34AM
Forum: Thermwood 3-Axis Machinery
Topic: Y axis Out of bounds
Replies: 8
Views: 145

Re: Y axis Out of bounds

I would start checking wires and connections - does it have the problem when just moving at the same location?
by tim lucas
Mon, May 28 2018, 8:14PM
Forum: eCabinet Systems Software
Topic: Adj shelf holes in corner cab
Replies: 4
Views: 199

Re: Adj shelf holes in corner cab

Better yet, look at the settings in this pic, notice we have all three colums checked to apply holes, on the right side I gave the back holes a negitive number (-3) so it would put the holes off the part and they would not show up. Set your cabinet to these settings and then take a look and see if t...
by tim lucas
Mon, May 28 2018, 8:03PM
Forum: eCabinet Systems Software
Topic: Adj shelf holes in corner cab
Replies: 4
Views: 199

Re: Adj shelf holes in corner cab

Post your corner cabinet if you can
by tim lucas
Sun, May 27 2018, 6:51AM
Forum: Lounge
Topic: Finished ends
Replies: 2
Views: 158

Re: Finished ends

we finish the ends also

What if the owner sees the cabinets without the appliance in place, would they think we provide quality if we dont finish the ends?

Tim
by tim lucas
Sun, May 27 2018, 6:48AM
Forum: eCabinet Systems Software
Topic: Adj shelf holes in corner cab
Replies: 4
Views: 199

Re: Adj shelf holes in corner cab

Andy,
Three holes would work as long as you use the shelf clips so they hold the top of the shelf. But myself I use 5 holes even with the clips.

Tim
by tim lucas
Fri, May 04 2018, 5:59AM
Forum: eCabinet Systems Software
Topic: Trouble cutting cabinet parts
Replies: 11
Views: 575

Re: Trouble cutting cabinet parts

I agree that in an ideal world I would not have to do any flip operations. Is it possible to set up blind dado joinery without flip operations? This particular cabinet I showed is a frameless 4 drawer cabinet with blind dados on the sides, top, and bottom, with a fully inset back. Alec The back is ...
by tim lucas
Wed, May 02 2018, 8:06PM
Forum: eCabinet Systems Software
Topic: Wish list
Replies: 4
Views: 236

Re: Wish list

You can add job items with cost - also you can add items to a cabinet -

hover over right side, select Job Buy List, or Cabinet Buy List, you may have to scroll to the bottom and / or scroll to the right to see Add Items to Job or Add Items To Assembly.

Not sure about hinge

Tim
by tim lucas
Mon, Apr 30 2018, 5:50AM
Forum: eCabinet Systems Software
Topic: Trouble cutting cabinet parts
Replies: 11
Views: 575

Re: Trouble cutting cabinet parts

It would be helpful to know what machine you are running or is this through the shopbot link?
Looking at your nest it may be ready for the flip opp to cut the back side dado then cut the out line, do you get any messages?

Tim
by tim lucas
Thu, Apr 26 2018, 5:42AM
Forum: eCabinet Systems Software
Topic: adj shelf height compartment not individually highlighting
Replies: 4
Views: 216

Re: adj shelf height compartment not individually highlighting

Instead of using your no cut wood, just use regular shelves then when you have them all set turn the shelves in phantom parts and they wont cut. you can change them back if you need to see them.
by tim lucas
Wed, Apr 25 2018, 4:25PM
Forum: eCabinet Systems Software
Topic: adj shelf height compartment not individually highlighting
Replies: 4
Views: 216

Re: adj shelf height compartment not individually highlighting

If I zoom in tight on a shelf I can select it and delete it, I deleted all shelves and can add shelves but after adding a couple the problem comes back. I tried with a standard frame-less cabinet and it works fine, not sure why your cabinet is corrupt? Do you have more cabinets that act the same way...
by tim lucas
Wed, Apr 18 2018, 6:40AM
Forum: eCabinet Systems Software
Topic: Suggestions on how to drill three sets of shelf pin holes
Replies: 9
Views: 430

Re: Suggestions on how to drill three sets of shelf pin holes

Is there a reason you cannot use shelf pin holes? You can mark the shelves as Phantom parts and they wont cut.

Tim
by tim lucas
Fri, Apr 06 2018, 6:58PM
Forum: Thermwood 3-Axis Machinery
Topic: Close call today, CNC fire
Replies: 5
Views: 435

Re: Close call today, CNC fire

Had it happen to me also, while cutting regular plywood a small part came loose, it rode the bit up and stayed with it while trying to cut the next part. It didn't take long and we had a 2 inch hole burning embers. Had a bottle of water near by, shut everything down and put it out. Can't leave those...
by tim lucas
Wed, Mar 21 2018, 6:33AM
Forum: Design Sharing
Topic: filing cabinets
Replies: 1
Views: 632

Re: filing cabinets

What do you mean?

Tim
by tim lucas
Sat, Mar 17 2018, 7:23AM
Forum: eCabinet Systems Software
Topic: Problem with Shopbot Link and Write to Shopbot
Replies: 3
Views: 414

Re: Problem with Shopbot Link and Write to Shopbot

Thanks for the update Don, hope they get it worked out

Tim

Go to advanced search