Search found 678 matches

by Forrest Chapman
Tue, Oct 24 2017, 10:28AM
Forum: eCabinet Systems Software
Topic: Corner door sizes
Replies: 2
Views: 139

Re: Corner door sizes

Rachel, according to your reveal and gap settings the doors are coming out correctly. 292mm on the left door and 2- 296.5mm doors on the right side. Here is the math for the left hand door. Left Front cabinet dim is 315mm - 3mm left reveal= 312mm- 18mm right door thickness= 294mm- 2mm for the door t...
by Forrest Chapman
Mon, Oct 23 2017, 10:38AM
Forum: eCabinet Systems Software
Topic: Corner door sizes
Replies: 2
Views: 139

Re: Corner door sizes

Rachel, I assume you're in beta? Moderators might wanna move this to the beta forum so you can get help. Only beta users can open the file so I'll take a look while I'm here to see if I can figure out whats going on.

Forrest
by Forrest Chapman
Fri, Oct 20 2017, 2:54PM
Forum: eCabinet Systems Software
Topic: Frameless cabinet drawer slide installation
Replies: 2
Views: 123

Re: Frameless cabinet drawer slide installation

While in cabinet editor click the "Drawer Slides" tab and under the drawer slide selection there is a "Hole Pattern" drop down. Select "clear default" and it will remove it from the cabinet.

Forrest
by Forrest Chapman
Tue, Oct 10 2017, 7:38AM
Forum: eCabinet Systems Software
Topic: constraint deletes hole
Replies: 4
Views: 204

Re: constraint deletes hole

Marcel, my drawers are done this way too. Its possible you may have a graphics issue. If you rebuild the drawer after making the constraints does the hole show up?

Ian is correct too that it should be w/2.

Forrest
by Forrest Chapman
Tue, Sep 12 2017, 10:40AM
Forum: Thermwood 3-Axis Machinery
Topic: thermwood desktop ctr nesting scroll issue
Replies: 9
Views: 581

Re: thermwood desktop ctr nesting scroll issue

Works for me!

Thanks, Forrest
by Forrest Chapman
Wed, Aug 23 2017, 1:53PM
Forum: eCabinet Systems Software
Topic: Hardware pattern Global Modification
Replies: 2
Views: 257

Re: Hardware pattern Global Modification

Make sure the cabinets to be changed are highlighted.

Forrest
by Forrest Chapman
Thu, Aug 03 2017, 9:38AM
Forum: Thermwood 3-Axis Machinery
Topic: thermwood desktop ctr nesting scroll issue
Replies: 9
Views: 581

Re: thermwood desktop ctr nesting scroll issue

Clint, I'm on 10. It's not a big pain but it was nice to just scroll without regard for where the mouse is.

Forrest
by Forrest Chapman
Tue, Aug 01 2017, 12:34PM
Forum: Thermwood 3-Axis Machinery
Topic: the new manual part placement feature
Replies: 5
Views: 621

Re: the new manual part placement feature

Clint, here are a couple other things I found with manual nesting. Once I started using the rotate option, whenever I clicked on the next part it rotated about 10 degrees on its own even if the rotate button was set back at 0. It would also be good if the rotate slider automatically goes back to 0 w...
by Forrest Chapman
Tue, Aug 01 2017, 12:10PM
Forum: Customer Tools
Topic: Improper Argument
Replies: 3
Views: 586

Re: Improper Argument

Rachelle, it looks like there are undercuts on the big radius's too. Sometimes the software doesn't like undercuts.

Forrest
by Forrest Chapman
Sat, Jul 29 2017, 8:46AM
Forum: Thermwood 3-Axis Machinery
Topic: thermwood desktop ctr nesting scroll issue
Replies: 9
Views: 581

Re: thermwood desktop ctr nesting scroll issue

Thomas, that is correct. One of the updates broke or removed that ability. Now you have to mouse over the sheet text block to scroll through the sheets. Maybe the loss of it was unintentional and they will fix it.

Forrest
by Forrest Chapman
Tue, May 23 2017, 8:38AM
Forum: eCabinet Systems Software
Topic: Keep Item box open while in batch
Replies: 2
Views: 550

Re: Keep Item box open while in batch

Hi Scott, I'm referring to the little popup box when you select a cabinet that you enter quantities and sizes. Once you click Add, the box goes away. It would be nice if it just stayed open allowing you to change say the quantity and width over and over again. I figure they can add a check box to &q...
by Forrest Chapman
Mon, May 22 2017, 3:29PM
Forum: eCabinet Systems Software
Topic: Keep Item box open while in batch
Replies: 2
Views: 550

Keep Item box open while in batch

It would be of benefit sometimes while adding items in batch if we had a check box to keep the item box open after adding said item. If we had multiple sizes of the same item we wouldn't have to re-select. This would come in handy for me when adding dovetail drawers that are the same height and dept...
by Forrest Chapman
Sat, Apr 15 2017, 3:56PM
Forum: eCabinet Systems Software
Topic: edging info missing on labels!
Replies: 7
Views: 847

Re: edging info missing on labels!

Update your graphics card drivers. That happens sometimes after a windows update so maybe it'll fix your issues.

Forrest
by Forrest Chapman
Mon, Feb 13 2017, 9:57AM
Forum: eCabinet Systems Software
Topic: problem with 6.1.4
Replies: 7
Views: 932

Re: problem with 6.1.4

Try updating your video card.

Forrest
by Forrest Chapman
Sun, Jan 29 2017, 12:27PM
Forum: Thermwood 3-Axis Machinery
Topic: Dust shroud/skirt alternatives
Replies: 5
Views: 1073

Re: Dust shroud/skirt alternatives

Also use a non-mortised tool so you have a longer upshear. With a 2 flute 3/8" comp tool turning 18k rpm you should be cutting at least 650ipm. This will make bigger chips that don't pack up as bad. You can also skin everything and then make a final pass. This will help remove all the dust but ...

Go to advanced search