Search found 90 matches

by jerry johnson
Sat, Jan 17 2015, 4:02PM
Forum: Thermwood 3-Axis Machinery
Topic: Carving rentals
Replies: 5
Views: 2463

Re: Carving rentals

Heirloom Oval 2.jpg
Heirloom Oval 1.jpg
Hi Josh. Been awhile since you responded to my post. Thanks! I sent you an e-mail with these pics. Hope you get it.
by jerry johnson
Tue, Aug 12 2014, 12:35PM
Forum: Thermwood 3-Axis Machinery
Topic: Carving rentals
Replies: 5
Views: 2463

Re: Carving rentals

Thanks for the reply Dennis. I no longer own my router (unfortunately) so I am looking for someone to maybe do the carving for me.
by jerry johnson
Sun, Aug 10 2014, 8:45PM
Forum: Thermwood 3-Axis Machinery
Topic: Carving rentals
Replies: 5
Views: 2463

Carving rentals

Is the carving rental program still available to Thermwood router owners? If so, is there anyone out there willing to give me some pricing for some carvings? I am in California.
Thanks!

Jerry Johnson
by jerry johnson
Mon, Jul 11 2011, 6:01PM
Forum: Thermwood 3-Axis Machinery
Topic: Hold Down Fixture
Replies: 16
Views: 4666

Re: Hold Down Fixture

New jamb part hold down board.pdf New jamb part hold down board.pdf Hi, Kerry. Unfortunately I no longer have my shop or my Thermwood router. However, I am working on another router and have had the opportunity to design and use gasketed boards for a multitude of applications especially in solid lu...
by jerry johnson
Mon, Jun 07 2010, 1:54PM
Forum: Thermwood 3-Axis Machinery
Topic: Cutting Solid Core Bamboo sheet
Replies: 4
Views: 1045

Re: Cutting Solid Core Bamboo sheet

Dave, I used a conventional cut. Will, I had to close my shop about nine months ago due to lack of work and lost my router. I was fortunate to be offered a job with a company here locally that does extreemley high end stuff as well as entry doors. The router I use is of a different make than Thermwo...
by jerry johnson
Fri, Jun 04 2010, 3:05PM
Forum: Thermwood 3-Axis Machinery
Topic: Cutting Solid Core Bamboo sheet
Replies: 4
Views: 1045

Re: Cutting Solid Core Bamboo sheet

Hi, Dave. I recently cut a large job with bamboo slab doors and experienced no problems. The bamboo was three ply and 19mm thick. I used a 1/2" compression bit and made all the cuts in one pass. The bamboo is hard so I did slow down the feed rates about 25%. 8)
by jerry johnson
Fri, Aug 21 2009, 8:25PM
Forum: Thermwood 3-Axis Machinery
Topic: Going out of business
Replies: 1
Views: 746

Going out of business

Hi, all. I have been a Thermwood and ecabinets user for the last two years and I cannot say enough positive about both. Unfortunatley, due to the severe decline in construction in California , not only am I losing my router but I am shutting down my shop. I purchased a CS 45 and I love the machine. ...
by jerry johnson
Tue, Jul 14 2009, 8:35PM
Forum: eCabinet Systems Software
Topic: Ease of Doing Curved Units?
Replies: 9
Views: 1798

Re: Ease of Doing Curved Units?

Hi, Nat. Yes, you can do radius work relatively easy in e-cabinets. Attached is a wine tasting room we did with a curved bar wall and tops. To generate the full renderings for the customer took about 10 hours but you can draw and cut the parts needed to fabricate the wall and sub tops in considerabl...
by jerry johnson
Mon, Jul 06 2009, 7:13PM
Forum: eCabinet Systems Software
Topic: Metric edgebanding
Replies: 1
Views: 453

Metric edgebanding

I just noticed that when in metric dimension mode I can only get the edgebanding to be 30480mm (100') long in the stock material setting. Is this normal? 8)
by jerry johnson
Wed, Jun 24 2009, 7:18PM
Forum: Thermwood 3-Axis Machinery
Topic: KD Rafix boring bits
Replies: 7
Views: 13726

Re: KD Rafix boring bits

Jason, are you using a Thermwood router? if so you do not need 10mm and 20mm bits as the router will cut the holes as a pocket using a smaller bit. 8)
by jerry johnson
Mon, Jun 22 2009, 7:24PM
Forum: eCabinet Systems Software
Topic: Drawer Slides, Different Types Same Cabinet?
Replies: 2
Views: 570

Re: Drawer Slides, Different Types Same Cabinet?

Nat, you can designate a different drawer box, drawer front, drawer slide, or drawer/drawer slide placement for each opening. Select an opening then the drawer/hardware details and add the drawer. Select another opening and you can change any or all of the original choices you made for the first ope...
by jerry johnson
Thu, Jun 11 2009, 7:55PM
Forum: Thermwood 3-Axis Machinery
Topic: More school fees
Replies: 3
Views: 994

Re: More school fees

Hey, Nick. When we cut thick mdf we use an up-cut two flute cutter and have no problems. 8)
by jerry johnson
Tue, Jun 02 2009, 6:29PM
Forum: eCabinet Systems Software
Topic: Toe Kick
Replies: 3
Views: 601

Re: Toe Kick

John, just add a stretcher to the cabinet and it will resize with the cabinet. Then you can use your pre-made sleepers. 8)
BACK TOE.jpg
BACK TOE.jpg (54.54 KiB) Viewed 640 times
by jerry johnson
Fri, May 22 2009, 9:57AM
Forum: Thermwood 3-Axis Machinery
Topic: Automatic oilers?
Replies: 6
Views: 1295

Re: Automatic oilers?

Terry, we had to mess with our oiler alot when we first got the machine. We turned up the oiler until there was oil running out everywhere and then backed it down. We had to put a small wood sliver in one of the lines, cock the block on the back of the gantry out of level, and make sure that the gla...
by jerry johnson
Sat, May 09 2009, 12:28PM
Forum: eCabinet Systems Software
Topic: Building a non-standard box
Replies: 8
Views: 1146

Re: Building a non-standard box

Like this, Adam.
TRASH BOX.jpg
TRASH BOX.jpg (34.87 KiB) Viewed 1187 times
8)

Go to advanced search