Something to think about. Wouldn't it be great if you could go into the door construction and change the location of the hinges even after the cabinet is done? Not only from left to right but also top and bottom.
this would be a huge time saver....
Search found 15 matches
- Sat, Feb 01 2020, 5:14PM
- Forum: eCabinet Systems Software
- Topic: Hinged Doors
- Replies: 9
- Views: 15603
- Thu, Oct 24 2019, 10:23PM
- Forum: Thermwood 3-Axis Machinery
- Topic: using barcode scanner to perform functions
- Replies: 3
- Views: 7330
using barcode scanner to perform functions
I am using a barcode scanner to scan off fall labels and I would like to be able to scan a code that opens up the EZ Off-Fall dialog box for the next input rather than have to go back to the keyboard. Is there a way to add shortcuts to functions within the program?
- Thu, Oct 17 2019, 9:42PM
- Forum: Thermwood 3-Axis Machinery
- Topic: Shelf Pin Notches
- Replies: 2
- Views: 9589
Shelf Pin Notches
I cut shelf pin notches on all my shelves. What you have to do is to insert a phantom adjustable shelf for the shelf holes and then add a fixed shelf with RTA joinery that is a simple notch. This works fine although it is tedious and you have to delete all the fixed shelves if you need to change the...
- Tue, Oct 15 2019, 1:32PM
- Forum: Thermwood 3-Axis Machinery
- Topic: Cordless barcode readers
- Replies: 4
- Views: 7871
Re: Cordless barcode readers
Thanks Tommy. Good to know and it makes sense. I bet a lot of people are doing the same thing.
- Sun, Oct 13 2019, 8:09PM
- Forum: eCabinet Systems Software
- Topic: drawer box losing RTA fittings
- Replies: 2
- Views: 5397
Re: drawer box losing RTA fittings
Hi Ralph. thanks for the reply. Unfortunately, these drawers were done in the drawer designer and saved to my drawers with the rafix fittings baked in. there is no reason that they should disappear and in fact, the pre-drilled screw hole which is another RTA fastener I the same drawer is not lost, o...
- Sat, Oct 12 2019, 2:51PM
- Forum: eCabinet Systems Software
- Topic: drawer box losing RTA fittings
- Replies: 2
- Views: 5397
drawer box losing RTA fittings
My drawer boxes are losing their rafix fittings every time I change something in the construction settings. I have to insert them again via Adj Features/Drawer Boxes with Drawer Fronts. This was happening before the update to 6.2.4 and still now. Has anyone else found this to be a problem? Is there ...
- Fri, Oct 11 2019, 8:49AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Cordless barcode readers
- Replies: 4
- Views: 7871
Re: Cordless barcode readers
thanks, Jeremy. I appreciate your input. I don't see how it could either but I was warned by my tech that the signals can interfere with the controller. I'm just looking for a way to improve the off-fall label scanning process and scanning away from the machine would be a bonus.
- Thu, Oct 10 2019, 4:41PM
- Forum: Thermwood 3-Axis Machinery
- Topic: Cordless barcode readers
- Replies: 4
- Views: 7871
Cordless barcode readers
I heard that Thermwood CNCs are allergic to anything that is cordless because of potential interference with the electronics. Is this still the case? If yes, would a USB hub with extended cable to the machine solve this problem? If not,is there a reason that a 15 foot usb extension not work with the...
- Wed, Jun 26 2019, 8:08AM
- Forum: eCabinet Systems Software
- Topic: CAB # in nested diagrams
- Replies: 3
- Views: 6304
Re: CAB # in nested diagrams
it would be great if we could change the B to another letter, the perfect example would be to help distinguish between B=Base and U=Upper and P=panel etc... It would also be great if we could have more control over the number as when you want to skip a number or start a different room at a different...
- Mon, Dec 04 2017, 10:30PM
- Forum: eCabinet Systems Software
- Topic: lock dado with single kd/rta not in center of small parts
- Replies: 1
- Views: 3766
lock dado with single kd/rta not in center of small parts
Has anyone found a way that you can use lock dado in a small part (4" stretcher) and use a single kd/rta fastener that is not centered so that the blind dado can take up the rest of the edge?
I tried centering my second kd/rta with a negative dimension but it still shows up off the edge.
thanks
I tried centering my second kd/rta with a negative dimension but it still shows up off the edge.
thanks
- Sun, Oct 18 2015, 9:12PM
- Forum: eCabinet Systems Software
- Topic: joinery between 2 cabinets in an assembly
- Replies: 6
- Views: 7883
Re: joinery between 2 cabinets in an assembly
Hi Kerry thanks for the explanation. I have tried adding an adjustable shelf to the outside of the cabinet and the joinery doesn't apply nor have I found a way to make the shelves come to the same level inside and out. see picture here: outside shelf.jpg its too bad that you can't save individual fu...
- Fri, Sep 25 2015, 8:26AM
- Forum: eCabinet Systems Software
- Topic: joinery between 2 cabinets in an assembly
- Replies: 6
- Views: 7883
joinery between 2 cabinets in an assembly
when you join 2 or more cabinets into an assembly, is there a way that the parts from one cabinet will cut the joinery on the adjoining parts on the second cabinet such as blind dado or RTA fasterner? i'm trying to afix a shelf on the outside of a cabinet and i can't figure out the right strategy to...
- Wed, Mar 25 2015, 10:22PM
- Forum: eCabinet Systems Software
- Topic: notched shelf for hiding the shelf pins
- Replies: 5
- Views: 6560
Re: notched shelf for hiding the shelf pins
Hi Nat
that's very clever, thank you very much. I'll try to see if i can work with this given that the rest of my cabinet is connected using regular KD fittings.
that's very clever, thank you very much. I'll try to see if i can work with this given that the rest of my cabinet is connected using regular KD fittings.
- Sat, Mar 21 2015, 10:43PM
- Forum: eCabinet Systems Software
- Topic: notched shelf for hiding the shelf pins
- Replies: 5
- Views: 6560
notched shelf for hiding the shelf pins
Is there any way to create a notch in the shelf that would hide the shelf pins like in the picture attached? I hate doing this in part editor and i suspect that there must be a better way.
thanks for your help
thanks for your help
- Mon, Nov 22 2010, 4:45PM
- Forum: eCabinet Systems Software
- Topic: Next Release Question
- Replies: 38
- Views: 30286
Re: Next Release Question
i would like to see a hybrid dado like this. i call it the interrupted dado with option for pilot holes. Jason, we've talked about this before and i can see that i'm not the only one who would like this. it wouldn't be very hard to do and it would set you apart from all your competitors. just imagin...