Search found 13 matches

by Paul Amos
Fri, Dec 04 2009, 8:15AM
Forum: eCabinet Systems Software
Topic: Face Frames for corner base cabinets
Replies: 3
Views: 1167

Re: Face Frames for corner base cabinets

Mark,

Why complicate things ?

Your method will still need dividers for the drawer runners and lots of 45degree cuts, you will probable need to assemble it on site unless you have wide access.

Can you not make 3 standard base cabinets 1 deep 2 shallow with the drawers in.


Paul
by Paul Amos
Sun, Oct 18 2009, 6:36AM
Forum: Lounge
Topic: Add Blind Dado to Stretcher?
Replies: 9
Views: 3745

Re: Add Blind Dado to Stretcher?

:D
by Paul Amos
Tue, May 12 2009, 1:00PM
Forum: Lounge
Topic: London Thermowood Operators?
Replies: 4
Views: 1955

Re: London Thermowood Operators?

Hi Dale,

A pre-welcome to you, I don't have aThermwood but I do have a Shopbot, I am awaiting my eCabinet link.

I am about 20 miles from Putney.

Let me know if I can be of assistance.

Paul
by Paul Amos
Thu, Apr 16 2009, 12:30PM
Forum: eCabinet Systems Software
Topic: Part Editor
Replies: 16
Views: 2903

Re: Part Editor

Thanks George,

I tried to apply some contraints to keep the flats either side of the arch the same size
when you alter the cabinets width but it would not except them.



Paul
by Paul Amos
Thu, Apr 16 2009, 10:40AM
Forum: eCabinet Systems Software
Topic: Part Editor
Replies: 16
Views: 2903

Re: Part Editor

Hi George,

What part did you create it from ?
Did you use the contour editor to create the shape ?


Many thanks

Paul
by Paul Amos
Thu, Apr 16 2009, 1:58AM
Forum: eCabinet Systems Software
Topic: Part Editor
Replies: 16
Views: 2903

Re: Part Editor

Kerry,

Thank you, that is exactly what I was looking for.


Paul
by Paul Amos
Wed, Apr 15 2009, 11:44AM
Forum: eCabinet Systems Software
Topic: Part Editor
Replies: 16
Views: 2903

Re: Part Editor

Rick Palechuk wrote:Post your cabinet Paul, maybe there is something else that can be done.


Rick,


Here is the cabinet, the L/R section will have doors the center section is open with an arched rail.


Any suggestions would be appreciated.



Paul
by Paul Amos
Tue, Apr 14 2009, 10:41AM
Forum: eCabinet Systems Software
Topic: Part Editor
Replies: 16
Views: 2903

Re: Part Editor

Thanks for the quick response,

I will have to use it with the stretcher and blind dado's so that it resizes with the cabinet, then re-machine the arch after.

What is planned for V6 and when will it be released ? No pressure.


Thanks


Paul
by Paul Amos
Tue, Apr 14 2009, 10:07AM
Forum: eCabinet Systems Software
Topic: Part Editor
Replies: 16
Views: 2903

Part Editor

I am trying to create an arched cutout to a L/R stretcher but the Part Editor says that this part type is not supported .....Any suggestions.


Thanks

Paul
by Paul Amos
Sun, Apr 12 2009, 5:21AM
Forum: eCabinet Systems Software
Topic: Resize Cabinet problem
Replies: 7
Views: 1576

Re: Resize Cabinet problem

I found the problem.........


In the constraints settings the first line of leg mounting holes had a setting of 11mm from the end of the panel, this was on the front and the back, I removed the contraint on the back and everything resized fine.
by Paul Amos
Sat, Apr 11 2009, 1:35PM
Forum: eCabinet Systems Software
Topic: Resize Cabinet problem
Replies: 7
Views: 1576

Re: Resize Cabinet problem

Ken,

I resized it before placing it.

Paul
by Paul Amos
Sat, Apr 11 2009, 8:07AM
Forum: eCabinet Systems Software
Topic: Resize Cabinet problem
Replies: 7
Views: 1576

Re: Resize Cabinet problem

Thanks Guys

Dan,

That's how I resized the cabinet.

Gary,

I tried your method and it worked fine, but I lost all the fitting holes, so I think it is a constraint issue.



Paul
by Paul Amos
Sat, Apr 11 2009, 5:21AM
Forum: eCabinet Systems Software
Topic: Resize Cabinet problem
Replies: 7
Views: 1576

Resize Cabinet problem

I look forward to joining the eCabinets forum now the software has been made available to Shopbot owners.


I need a bit of help, please.

I am try to resize a cabinet from the frameless 32 system, everything resizes ok except the base, what am I doing wrong ?

Paul

Go to advanced search