Search found 431 matches

by Nat Wheatley
Thu, Feb 07 2019, 11:45AM
Forum: eCabinet Systems Software
Topic: Looking for an edgebanding setting
Replies: 2
Views: 4584

Re: Looking for an edgebanding setting

Believes this thread will show what you're looking to do:

http://www.thermwood.com/forums/viewtop ... components
by Nat Wheatley
Mon, Nov 26 2018, 9:13AM
Forum: eCabinet Systems Software
Topic: Shop Drawings
Replies: 4
Views: 6601

Re: Shop Drawings

No solution from me, but good to see you around Kerry.
by Nat Wheatley
Tue, Aug 07 2018, 8:04AM
Forum: eCabinet Systems Software
Topic: Edgebanding Appearing without being Applied
Replies: 3
Views: 5919

Re: Edgebanding Appearing without being Applied

Thanks Jeremy. For some reason I've never even seen that tab before...
by Nat Wheatley
Mon, Aug 06 2018, 5:15PM
Forum: eCabinet Systems Software
Topic: Edgebanding Appearing without being Applied
Replies: 3
Views: 5919

Edgebanding Appearing without being Applied

I'm building a new library of cabinets and any time I add an 'up-down/ stretcher', it automatically applies edgebanding to the top edge. Have I got a setting somewhere turned on for this that's causing it to do this? Thanks
by Nat Wheatley
Mon, Aug 06 2018, 5:04PM
Forum: eCabinet Systems Software
Topic: Trouble Opening Cabinets
Replies: 5
Views: 7891

Re: Trouble Opening Cabinets

Hi, I was just syncing the cabinets folder only.
by Nat Wheatley
Mon, Aug 06 2018, 2:29PM
Forum: eCabinet Systems Software
Topic: Full Dado with Pilot Holes?
Replies: 11
Views: 13720

Re: Full Dado with Pilot Holes?

Got it, thanks very much for the help.
by Nat Wheatley
Mon, Aug 06 2018, 11:06AM
Forum: eCabinet Systems Software
Topic: Full Dado with Pilot Holes?
Replies: 11
Views: 13720

Re: Full Dado with Pilot Holes?

Thanks Jeremy. Are those the pilot holes done with the spot holes for pocket screws? If so, were you also able to eliminate the pocket for the pocket screws?

Nat
by Nat Wheatley
Mon, Aug 06 2018, 6:20AM
Forum: eCabinet Systems Software
Topic: Create Seam?
Replies: 3
Views: 5618

Re: Create Seam?

That sounds promising, I'll give it a try. Thanks very much.
by Nat Wheatley
Sun, Aug 05 2018, 2:14PM
Forum: eCabinet Systems Software
Topic: Full Dado with Pilot Holes?
Replies: 11
Views: 13720

Full Dado with Pilot Holes?

Is there a way to add pilot holes to a full dado joint?
by Nat Wheatley
Fri, Aug 03 2018, 3:24PM
Forum: eCabinet Systems Software
Topic: Trouble Opening Cabinets
Replies: 5
Views: 7891

Re: Trouble Opening Cabinets

Thanks Tim. I was syncing my 'cabinets' folder with Google Drive and am just now realizing that that may be causing the problem. I've turned the syncing off for that folder, tried saving and opening several cabinets, and so far the error message seems to have stopped. Fingers crossed...
by Nat Wheatley
Thu, Aug 02 2018, 1:58PM
Forum: eCabinet Systems Software
Topic: Create Seam?
Replies: 3
Views: 5618

Create Seam?

I realize that this may be a long shot, but is there a way to create a seam in a part? In other words break a part into 2 pieces when it's longer than the sheet stock that it will be cut from.
by Nat Wheatley
Wed, Aug 01 2018, 4:29PM
Forum: eCabinet Systems Software
Topic: Trouble Opening Cabinets
Replies: 5
Views: 7891

Re: Trouble Opening Cabinets

Anyone?
by Nat Wheatley
Sun, Jul 29 2018, 2:21PM
Forum: eCabinet Systems Software
Topic: Trouble Opening Cabinets
Replies: 5
Views: 7891

Trouble Opening Cabinets

I'm having issues trying to open cabinets that I've saved in the cabinet editor. I get a series of error messages starting with 'unable to open Ecabinets data file', then 'there was a problem reading HSF', then 'problem loading single cabinet' Sometimes when I rename the cabinet i's able to open it,...
by Nat Wheatley
Sun, Jul 08 2018, 2:38PM
Forum: eCabinet Systems Software
Topic: Flip Ops in SB Link
Replies: 12
Views: 12149

Re: Flip Ops in SB Link

My machine is fairly well tuned for this, but could definitely use a little more attention there. I've been doing 2 sided machining on my parts, but using a roundabout kind or way to do it...
by Nat Wheatley
Sun, Jul 08 2018, 2:25PM
Forum: eCabinet Systems Software
Topic: Flip Ops in SB Link
Replies: 12
Views: 12149

Re: Flip Ops in SB Link

(Sorry, posted this before I saw your last post, reading that now...) Thanks Ralph, that work around sounds ideal. The most recent version I'm seeing is 1.21.3 (which I don't see that that added feature to nest the flip ops together) but I'll check my shop computer to see what version is loaded ther...

Go to advanced search