Search found 287 matches

by Mark McCallum
Tue, May 12 2020, 5:06AM
Forum: eCabinet Systems Software
Topic: Angle part
Replies: 3
Views: 644

Re: Angle part

Hi Rob. My take. I couldn't see the angle or really understand what you were referring to until I had been messing with an idea and eventually saw the angled front frame in your cabinet. So I had been messing with what I thought you meant. Perhaps it might be useful? I deleted the back and made the ...
by Mark McCallum
Thu, Apr 23 2020, 6:45PM
Forum: Thermwood 3-Axis Machinery
Topic: Nesting a large number of small pieces
Replies: 2
Views: 718

Re: Nesting a large number of small pieces

Thanks Clint. I will look into that. :D I'm just wondering if they could stop that " ANOTHER SETTING button from moving around. :) Sometimes it is just under "settings" sometime under "tools" sometimes it "just moves all over the place"! If it would just stay in th...
by Mark McCallum
Thu, Apr 23 2020, 6:33PM
Forum: Thermwood 3-Axis Machinery
Topic: Control nesting loaded material board sizing
Replies: 2
Views: 866

Re: Control nesting loaded material board sizing

Thanks Clint. It would be a good one to get fixed. :D It always happens on the first sheet of a nest. The one with all the flip ops. :? So you miss the first one, get a new sheet, apply size change, forget to do it twice to make it apply, cut, slap forehead and go duhhhh, I am so dumb, get another s...
by Mark McCallum
Thu, Apr 23 2020, 12:39AM
Forum: Thermwood 3-Axis Machinery
Topic: Nesting a large number of small pieces
Replies: 2
Views: 718

Nesting a large number of small pieces

In the attached photo we cut 120 of these at a time, (The pieces we use are removed and this is the waste) Control nesting seems to get to about 100 pieces and then says this is all too hard, I'll just stickem where I can. The yield goes down a little bit once the grid like nesting drops off. Does t...
by Mark McCallum
Fri, Apr 10 2020, 6:17AM
Forum: Thermwood 3-Axis Machinery
Topic: Control nesting loaded material board sizing
Replies: 2
Views: 866

Control nesting loaded material board sizing

A little quirk I have noticed on our machine and wonder if it happens to anyone else. Load a job into control nesting. Go okay to get to the nesting screen Hit nest x or y. The loaded material dialogue comes up where it is possible to change the sheet dimensions, as in the attached photo. Change siz...
by Mark McCallum
Sat, Mar 21 2020, 8:11PM
Forum: Lounge
Topic: Strength in solidarity by isolation
Replies: 0
Views: 2231

Strength in solidarity by isolation

Just hoping all my fellow industry associates can come through these (what are probably going to be) very tough times. I hope all our elder friends and family members come through. We are all in this together Be sensible and stay strong Probably a good time to sort out libraries, track down those ra...
by Mark McCallum
Sat, Mar 21 2020, 7:52PM
Forum: eCabinet Systems Software
Topic: Maybe this operation can be changed?
Replies: 2
Views: 2107

Re: Maybe this operation can be changed?

Hi Donald
Perhaps if you post a sample cabinet
I cant visualize what you are describing.
by Mark McCallum
Sat, Mar 21 2020, 7:13PM
Forum: eCabinet Systems Software
Topic: What is wrong with this cabinet?
Replies: 14
Views: 2240

Re: What is wrong with this cabinet?

Ki Kerry
I get the same message with your cabinets.
by Mark McCallum
Fri, Jan 31 2020, 4:39AM
Forum: eCabinet Systems Software
Topic: Profile edge issue
Replies: 3
Views: 1916

Re: Profile edge issue

Hi JR Just testing and yes I experience a similar thing. In the attached piece it has pockets I can select the bottom edge click the left hand edge and it selects 3 more edges or says there was a para solid error creating a new part body. If I remove part editor parts from entire cabinet in the cabi...
by Mark McCallum
Fri, Jan 31 2020, 3:50AM
Forum: eCabinet Systems Software
Topic: Add Notes to Custom Layout
Replies: 1
Views: 1621

Re: Add Notes to Custom Layout

That would be wonderful! Ecabs version7 :lol: I would like to be able to save notes with cabinets as well. Just so you can note little things like fixed such and such or needs adjusting to suit. or doors with bigger reveal LHS and it would display in the lower left hand corner of the cabinet editor....
by Mark McCallum
Thu, Jan 02 2020, 4:39AM
Forum: eCabinet Systems Software
Topic: Showing no Grain material in Cabinet /editor all showes White
Replies: 2
Views: 1771

Re: Showing no Grain material in Cabinet /editor all showes White

Hi Elie
Some things to look at. perhaps
1st check these settings
The image you have selected might be white? if so choose a grained one.

Grain-direction.jpg

Then check these settings

Grain-direction2.jpg


If that doesnt work, perhaps give us an update.

Hope that helps
by Mark McCallum
Sun, Nov 10 2019, 8:08AM
Forum: eCabinet Systems Software
Topic: Edit Depth not working in Constraint Manager
Replies: 5
Views: 3626

Re: Edit Depth not working in Constraint Manager

If there is a depth constraint, you cannot use Edit Depth. - If there is no depth constraint, you are not selecting a node, you just need to click on the geometry. So if there is a constraint already just click on the constraint? I seem to remember that it worked like Joe described before.? https:/...
by Mark McCallum
Wed, Nov 06 2019, 4:19PM
Forum: eCabinet Systems Software
Topic: Applied ends
Replies: 3
Views: 2731

Re: Applied ends

Thanks Guys
Hi Ralph,
No Gremlins (only the one in my brain)
Ian surmised it correctly.
I have used the applied end feature quiet a bit and its great for setting up kitchens in custom layout.
I hadn't used it myself for about 6 months and forgot the selection methods.
Thanks for the help :)
by Mark McCallum
Tue, Nov 05 2019, 4:50PM
Forum: eCabinet Systems Software
Topic: Applied ends
Replies: 3
Views: 2731

Applied ends

Is anyone else using applied ends and having troubles deleting them? In the attached cabinet, I cant delete the right panel. Its a little bit intermittent.The left end applied end also plays up for me as well, but in this example it deletes. Std Base Frameless.jpg Std Base Frameless.hsf Applied ends...
by Mark McCallum
Tue, Nov 05 2019, 4:00PM
Forum: eCabinet Systems Software
Topic: Edit Depth not working in Constraint Manager
Replies: 5
Views: 3626

Re: Edit Depth not working in Constraint Manager

Hi Joe
I get the same results.
Its like its meant to work that way. :D

Go to advanced search