Search found 310 matches
- Sat, Apr 03 2021, 2:43AM
- Forum: eCabinet Systems Software
- Topic: Cabinet with angled ends or tops
- Replies: 1
- Views: 100
Re: Cabinet with angled ends or tops
I should have mentioned in the post above, while you can add a vertical stretcher like a partition, as far as I can determine, you can only rotate it in one dimension, that being while looking at the front of the cabinet it behaves like a revolving door into a building. The same situation with a par...
- Fri, Apr 02 2021, 10:27AM
- Forum: eCabinet Systems Software
- Topic: An Active Forum is a Strong Forum
- Replies: 17
- Views: 2306
Re: An Active Forum is a Strong Forum
Hi Rob Thanks for your feedback. Nice wine rack......... (Where is all the wine? :) ) I agree its very good software, super good most of the time. I feel so much pleasure with all the work we put into programing a job, and it just cuts everything out, and its like, Wow, that's just amazing! its like...
- Fri, Apr 02 2021, 8:59AM
- Forum: eCabinet Systems Software
- Topic: Cabinet with angled ends or tops
- Replies: 1
- Views: 100
Cabinet with angled ends or tops
Its been asked a few times if its possible to angle sides or tops of cabinets. I have to do a cabinet for an under stair situation and came up with a method by using stretchers. Stretchers are a wonderful tool and with a bit of practice you can do some amazing things. The main thing to think about i...
- Tue, Feb 23 2021, 6:45AM
- Forum: eCabinet Systems Software
- Topic: An Active Forum is a Strong Forum
- Replies: 17
- Views: 2306
Re: An Active Forum is a Strong Forum
Hi Guys Can you get the same result? I have attached 2 cabinets because they are too big to upload as an assembly 1) load both units into the cabinet editor 2) select either cabinet and global modify any sheet material and replace with new material of the same thickness. Select either cabinet . Use ...
- Wed, Feb 03 2021, 3:41AM
- Forum: eCabinet Systems Software
- Topic: Top shelf looses alignment points
- Replies: 1
- Views: 783
Re: Top shelf looses alignment points
I persisted with this corner one, because it seemed to have come good, I had put a fair bit of time into it already, and didn't want to restart from scratch. However I forgot to monitor it at the machine. And even if I had noticed the missing info we have to get the job out anyway. And redoing it wo...
- Mon, Feb 01 2021, 7:23PM
- Forum: eCabinet Systems Software
- Topic: An Active Forum is a Strong Forum
- Replies: 17
- Views: 2306
Re: An Active Forum is a Strong Forum
Hi Donald Cint has saved the bacon again. :) Clint sent me an email saying the top drawer behind the doors is messed up. One of those gremlins. I haven't touched that drawer since I designed the cabinet 2 months ago. Don't know why it all of a sudden lost its brains..... Yes its those things that co...
- Mon, Feb 01 2021, 7:15PM
- Forum: eCabinet Systems Software
- Topic: An Active Forum is a Strong Forum
- Replies: 17
- Views: 2306
Re: An Active Forum is a Strong Forum
Hi Stuart (After working through similar problems in eCabS, I too can attest to the absolutely USELESS error messages. If the dialog told me what damn rabbit to chase, then I would gladly do it. As others had stated, It's usually operator error, and all you need is a clue about which part or operati...
- Mon, Feb 01 2021, 5:59PM
- Forum: eCabinet Systems Software
- Topic: An Active Forum is a Strong Forum
- Replies: 17
- Views: 2306
Re: An Active Forum is a Strong Forum
(When I am in the Design phase, I will usually just tough it out, redraw, redo, what ever it takes. Change software if necessary.) Sounds pretty much what I do :) (Since I no longer try to import dxf files into control nesting.) I still do import DXF's. Yes, they can and do give problems. but 80% o...
- Mon, Feb 01 2021, 5:13PM
- Forum: eCabinet Systems Software
- Topic: An Active Forum is a Strong Forum
- Replies: 17
- Views: 2306
Re: An Active Forum is a Strong Forum
Hi Donald
I get the same error message when nesting your unit.
When I remove part editor cuts from the entire cabinet it nests.
I get the same error message when nesting your unit.
When I remove part editor cuts from the entire cabinet it nests.
- Sat, Jan 30 2021, 7:46PM
- Forum: eCabinet Systems Software
- Topic: An Active Forum is a Strong Forum
- Replies: 17
- Views: 2306
Re: An Active Forum is a Strong Forum
Hi Donald. Thats good I think posting the messages helps. Also posting the cabinet here if you don't mind sharing the design. (Some cabinets can be special and have hours of design put into them so I can fully understand not wanting to) If others are then interested in testing the unit and reporting...
- Thu, Jan 28 2021, 10:56PM
- Forum: eCabinet Systems Software
- Topic: An Active Forum is a Strong Forum
- Replies: 17
- Views: 2306
An Active Forum is a Strong Forum
Just curious Lately we are having some flops. Cabinets or assemblies are fine up to a certain point then, information drops off or out of the file. Sometimes its on a new design, some times its on single cupboards and other times its on assemblies, sometimes it seems to be on month or older file tha...
- Thu, Jan 28 2021, 6:36PM
- Forum: eCabinet Systems Software
- Topic: Calc countertop sq ft
- Replies: 1
- Views: 676
Re: Calc countertop sq ft
Hi Donald. Yes I see what you mean. I dont know of a way. We dont use the countertop section for various reasons. The way we do it is to create a material for benchtops. We then use a standard cabinet with only the top remaining. You can set it up as per job requirements with benchtop joins. or Ofte...
- Fri, Jan 15 2021, 7:04AM
- Forum: eCabinet Systems Software
- Topic: Top shelf looses alignment points
- Replies: 1
- Views: 783
Top shelf looses alignment points
In the attached corner cupboard It is a square corner front with an applied Chamfer in the part editor. CF Wip Top.jpg CF Wip Top.hsf To rebuild the top shelf I am in the main screen. Highlight cabinet, green hash top shelf. right mouse click Select remove part editor cuts select , from selected par...
- Fri, Jan 15 2021, 6:21AM
- Forum: eCabinet Systems Software
- Topic: Drawing Walls in Custom Layout
- Replies: 1
- Views: 749
Re: Drawing Walls in Custom Layout
Hi Kerry Not sure if it helps. On my computer if I drag the wall end up to the edge of the workspace with the mouse and hover without clicking, it sort of zooms out, pull across or down more hover on the workspace edge, zooms out. The wall length updates in the length window as I drag, When I am ove...
- Fri, Jan 15 2021, 6:04AM
- Forum: eCabinet Systems Software
- Topic: Notes in Custom Layout
- Replies: 3
- Views: 1150
Re: Notes in Custom Layout
Hi Kerry Thats a Genius level work around :beer: I would love to see the white board in the programers office. Yes Tick maybe tick maybe tick maybe tick Nup Nup Nup Seriously ... Nup Aint gonna happen Aint gonna happen Aint gonna happen...................................................................