Search found 595 matches

by Nick M Singer
Sat, Jan 07 2012, 5:44AM
Forum: eCabinet Systems Software
Topic: Blum Intivo
Replies: 19
Views: 7988

Re: Blum Intivo

Dynaplan is superfluous if you are using eCabs, all you do is create a drawer which only has a back back and a bottom (I used a blind dado joint for the back into the bottom) you specify the correct left and right insets for the back upstand in the drawer construction parameters. the hole pattern ca...
by Nick M Singer
Fri, Jan 06 2012, 12:26AM
Forum: eCabinet Systems Software
Topic: Blum Intivo
Replies: 19
Views: 7988

Re: Blum Intivo

Hi Josh, before I closed up shop I was using eCabs with both Metabox and Tandembox for machining on my Thermwood (Intivo is pretty much the same as Tandembox), it is pretty simple to do, what do you find a problem?
by Nick M Singer
Tue, Jul 12 2011, 1:25AM
Forum: eCabinet Systems Software
Topic: Sliding Doors
Replies: 1
Views: 571

Re: Sliding Doors

Mark you can place doors with the required inset to simulate sliding doors using the door/drawer editor and they will automatically re-size. The only complication is the different placements to get one behind the other especially as you have a pair of doors in one opening. The solution to this would...
by Nick M Singer
Sun, Feb 20 2011, 12:27AM
Forum: eCabinet Systems Software
Topic: Sink cut out in counter top
Replies: 4
Views: 754

Re: Sink cut out in counter top

Tim put a light in at a lower level
by Nick M Singer
Sun, Jan 30 2011, 11:58PM
Forum: eCabinet Systems Software
Topic: Clipping a TK corner
Replies: 4
Views: 702

Re: Clipping a TK corner

Brian, I assume you are trying to cut a miter on each end of the kick plate? If so then all you need do is apply an appropriate tool to those ends in a profiling operation
by Nick M Singer
Sun, Jan 16 2011, 12:46AM
Forum: eCabinet Systems Software
Topic: Trouble with lighting
Replies: 10
Views: 1378

Re: Trouble with lighting

Gary it is not just a matter of the number of lights it is also where you place them, the intensity settings and the type of light you select. Try for starters turning down the intensity of all the lights you have to get rid of that washed out look. What I sometimes do is put some lights underneath ...
by Nick M Singer
Thu, Jan 13 2011, 11:14PM
Forum: eCabinet Systems Software
Topic: Clipped Corner Oops!
Replies: 1
Views: 481

Re: Clipped Corner Oops!

John I have done this kind of thing before but I am afraid it is a job for the part editor
by Nick M Singer
Tue, Jan 11 2011, 11:40PM
Forum: eCabinet Systems Software
Topic: Would it be possible?
Replies: 2
Views: 655

Re: Would it be possible?

Do you mean possible as a future feature or can you do it now? You could do it now but you would have to create the wall yourself out of face frame cabs with everything switched off except the frames and the doors
by Nick M Singer
Sun, Jan 09 2011, 10:03AM
Forum: Thermwood 3-Axis Machinery
Topic: New style locator pins
Replies: 6
Views: 1381

Re: New style locator pins

Ben something you may consider trying which I did is buying and fixing 4 small pneumatic pistons onto the edge of the table in the correct locations to serve as pop up pins.
by Nick M Singer
Wed, Jan 05 2011, 6:00AM
Forum: eCabinet Systems Software
Topic: convert to dxf
Replies: 1
Views: 483

Re: convert to dxf

No
by Nick M Singer
Wed, Nov 24 2010, 11:51PM
Forum: Thermwood 3-Axis Machinery
Topic: Replacement Printer for Thermwood CS40
Replies: 5
Views: 1314

Re: Replacement Printer for Thermwood CS40

Steve I mean what is the opening size provided in the cabinet for the printer? As I said I sourced my own printer and built my own cab and had no trouble with my small HP laser printer for over 5 years now.
by Nick M Singer
Sun, Nov 14 2010, 9:01AM
Forum: Thermwood 3-Axis Machinery
Topic: Help with DXF
Replies: 26
Views: 4143

Re: Help with DXF

Or if I knew what the font was i can regenerate the letters with my CAD program which should give a better result
by Nick M Singer
Sun, Nov 14 2010, 8:55AM
Forum: Thermwood 3-Axis Machinery
Topic: Replacement Printer for Thermwood CS40
Replies: 5
Views: 1314

Re: Replacement Printer for Thermwood CS40

I have been using the same HP laser printer built into a cabinet at the controller for 5 years without any problem. What is the size of the aperture for the printer you have?
by Nick M Singer
Fri, Nov 12 2010, 11:50PM
Forum: Thermwood 3-Axis Machinery
Topic: Help with DXF
Replies: 26
Views: 4143

Re: Help with DXF

Hi Brian. Here is the DXF. I looked at the letters close up and I can see why they are machining rough. All the curves are made up of small segmens instead of arcs, this would not be so bad if they flowed into each other but in this case they zig zag along. In a nutshell the letters need to be compl...
by Nick M Singer
Thu, Nov 11 2010, 11:02AM
Forum: Thermwood 3-Axis Machinery
Topic: Help with DXF
Replies: 26
Views: 4143

Re: Help with DXF

Brian try this on a piece of scrap board and see how it goes. There will be errors but I just want to see if it machines at all. Also what depth do you want to cut at? I have set it at 10mm and used a 16mm display panel. Sorry about all the time delay and the metric I am in South Africa

Go to advanced search