Search found 45 matches
- Sun, Dec 01 2013, 5:28AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Locating pins
- Replies: 5
- Views: 7720
Re: Locating pins
Awesome setup Dave. Where did you get the threaded shafts from?
- Tue, Jul 09 2013, 10:39AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Cut3D Post Processor
- Replies: 1
- Views: 4243
Re: Cut3D Post Processor
This works with Cut3D
You have to remove line 77 which has command to list tools
Save as *.pp and copy and paste into PostP folder of cut3D
http://www.thermwood.com/forums/viewtop ... rve#p69489
You have to remove line 77 which has command to list tools
Save as *.pp and copy and paste into PostP folder of cut3D
http://www.thermwood.com/forums/viewtop ... rve#p69489
- Mon, Jul 08 2013, 4:47PM
- Forum: Thermwood 3-Axis Machinery
- Topic: Cut3D Post Processor
- Replies: 1
- Views: 4243
Cut3D Post Processor
Does anyone have a post processor for Cut3D?
- Sun, Apr 28 2013, 8:58AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Shaker doors
- Replies: 1
- Views: 4471
Shaker doors
I am looking to efficiently cut shaker door frames with eCabs and control nesting. My rail size is 2-1/4" and the rabbet is 3/8" wide by 1/2" deep in 3/4" MDF. Does anyone have the silver bullet?
- Tue, Jan 08 2013, 4:46PM
- Forum: eCabinet Systems Software
- Topic: Beaded face Frames
- Replies: 2
- Views: 5766
Re: Beaded face Frames
Try these. Use the bead tool for edge profile on stiles and rails. The cabinet doors and drawers are .75" inset.
- Wed, Dec 12 2012, 4:53AM
- Forum: eCabinet Systems Software
- Topic: Closet suspension rails
- Replies: 2
- Views: 5468
Re: Closet suspension rails
The notch is 4" so that you can install the cabinet on the rail without a fight.
- Mon, Nov 19 2012, 9:24PM
- Forum: eCabinet Systems Software
- Topic: Some suggestions for future updates
- Replies: 7
- Views: 8462
Re: Some suggestions for future updates
3) Create a cabinet with only the back. Have the back flush with all sides. Save it as "AAA_Display panel" so it is easy to find in your library. IE. a 20"x20" cabinet would leave you with just the back at 20"x20". You can change the size after you load it. This will al...
- Sat, Nov 03 2012, 10:19AM
- Forum: eCabinet Systems Software
- Topic: Slot Slide Settings
- Replies: 4
- Views: 6765
Re: Slot Slide Settings
This is a part of the youbuildit furniture construction.
- Tue, Oct 09 2012, 3:32AM
- Forum: eCabinet Systems Software
- Topic: Importing .DXF in Contour mgr
- Replies: 4
- Views: 6716
Re: Importing .DXF in Contour mgr
Thanks Rick.
- Sun, Oct 07 2012, 4:37AM
- Forum: eCabinet Systems Software
- Topic: Importing .DXF in Contour mgr
- Replies: 4
- Views: 6716
- Sat, Oct 06 2012, 11:30AM
- Forum: eCabinet Systems Software
- Topic: Importing .DXF in Contour mgr
- Replies: 4
- Views: 6716
Importing .DXF in Contour mgr
When I go to open .DXF files into Contour Mgr., I get the following error;
"The unregistered version is for evaluation only
Purchase at www.cadsofttools.com.
Has anyone encountered this? What is the solution?
"The unregistered version is for evaluation only
Purchase at www.cadsofttools.com.
Has anyone encountered this? What is the solution?
- Mon, Aug 06 2012, 11:08AM
- Forum: eCabinet Systems Software
- Topic: New PC
- Replies: 3
- Views: 5118
Re: New PC
Thanks Rick:
I'm looking to see Manufacturer/model/specs others are going with...
I'm looking to see Manufacturer/model/specs others are going with...
- Mon, Aug 06 2012, 10:21AM
- Forum: eCabinet Systems Software
- Topic: New PC
- Replies: 3
- Views: 5118
New PC
Looking at buying a new PC and wanted to see what eCab folks are using.
- Wed, Jul 25 2012, 12:13PM
- Forum: Design Sharing
- Topic: MDF door with X
- Replies: 0
- Views: 14727
MDF door with X
This is an MDF door that is the back of a cabinet. The back is set flush, 1/16" inset on top, deck, L&R sides. There is no top, deck or sides on this cabinet. This allows the door to be 1/8" less than the cabinet size L & W. The pattern is constrained to give 2-3/8" stiles and...
- Mon, Apr 09 2012, 4:11PM
- Forum: eCabinet Systems Software
- Topic: Barb Dado
- Replies: 3
- Views: 4995
Re: Barb Dado
Do not use with Particle core
. Works okay with veneer core. Works best with MDF core. Overall, the joints hold secure but they are not as tight as can be achieved with screws. The application is nice when you have a finished end.
![Frustrated :wall:](./images/smilies/pictowallsmall.gif)