Search found 11 matches

by Jason Lacireno
Tue, Jun 27 2017, 9:03AM
Forum: Thermwood 3-Axis Machinery
Topic: the new manual part placement feature
Replies: 5
Views: 620

Re: the new manual part placement feature

I enjoy the new Feature. its a pretty Game changer for me. yeah couple small glitches mentioned here but i still love it.

I've played with this new feature quite a bit and pretty used to it now.
by Jason Lacireno
Mon, Jan 16 2017, 7:44AM
Forum: Thermwood 3-Axis Machinery
Topic: Cut-out instead of pocket
Replies: 13
Views: 1570

Re: Cut-out instead of pocket

is it drawn up to cut all the way through or just a pocket? because i'm not sure of any other reason it would do this. write the program. do CTRL+F ...look in the programming to see if it does a (pocket clean up) or (pocket rout). if it does a pocket Rout...then you need to re draw that pocket to cu...
by Jason Lacireno
Mon, Jan 16 2017, 7:30AM
Forum: Thermwood 3-Axis Machinery
Topic: Cut-out instead of pocket
Replies: 13
Views: 1570

Re: Cut-out instead of pocket

are you using groups?

make sure your changing the setting for the apropriate group.

my cleanup amount is always at 0" ...your settings look fine to me though.
by Jason Lacireno
Mon, Aug 15 2016, 7:35AM
Forum: Thermwood 3-Axis Machinery
Topic: control upgrade
Replies: 20
Views: 3570

Re: control upgrade

We upgraded my C-40 when we bought the CS-43, i think the C-40 over 10 years old

I had windows 2000 on it with weak hardware.

now its upgraded, expensive but affective. nesting time is reduced quite a bit, i wouldnt say cut in half but its much faster.
by Jason Lacireno
Thu, Jul 07 2016, 6:02AM
Forum: Thermwood 3-Axis Machinery
Topic: CS 43 error
Replies: 3
Views: 2248

Re: CS 43 error

We Replaced the 24v power supply.

Solved the problem.

I enjoyed the down time while it lasted. Thanks. :D :)
by Jason Lacireno
Mon, Jul 04 2016, 9:29AM
Forum: Thermwood 3-Axis Machinery
Topic: CS 43 error
Replies: 3
Views: 2248

Re: CS 43 error

Bumping this thread since i now have the same problem.

The only power i have is the Computer, nothing else.

Thanks.
by Jason Lacireno
Mon, Feb 29 2016, 9:59AM
Forum: Thermwood 3-Axis Machinery
Topic: Feed Rate Dropping (cs-40)
Replies: 2
Views: 1637

Re: Feed Rate Dropping (cs-40)

Thanks for the Reply Carl.

I found a loose white wire with the light blue stripe on the back wall inside the control panel. the screw was almost out completely so i tightenned it up.

I will post a message here by the end of the week with the results.

Hope that was it :)

thanks again!!!
by Jason Lacireno
Wed, Feb 17 2016, 10:20AM
Forum: Thermwood 3-Axis Machinery
Topic: Feed Rate Dropping (cs-40)
Replies: 2
Views: 1637

Feed Rate Dropping (cs-40)

CS-40 computer hardware Gutted and Upgraded to windows 7. After about 2 and a half years of the new upgrade, Feed Rate dropping from 120% to the 90's and 80 percentiles. Changed the adjuster switch and it still does it. I tap the side of the machine and sometimes it jumps back to normal 120% and so...
by Jason Lacireno
Tue, Mar 26 2013, 7:19AM
Forum: Thermwood 3-Axis Machinery
Topic: Improve Dust Pickup CS43
Replies: 33
Views: 11463

Re: Improve Dust Pickup CS43

This Explains why would be extremely difficult to change Depth of the Bowl...

The tool holders on the C-40 are on stilts wich allow for a deeper grab, unlike the CS-43 wich cant go too far down because of the table...sucks...need try to make the vacuum pathway diameter bigger somehow :?
by Jason Lacireno
Thu, Mar 14 2013, 6:19PM
Forum: Thermwood 3-Axis Machinery
Topic: Improve Dust Pickup CS43
Replies: 33
Views: 11463

Re: Improve Dust Pickup CS43

See...the problem is not Vacuum...the Suction is great when the flex tube is disconnected...its the yellow Bowl itself.... was wrongly made...The bowl itself reduces the diameter, and a slot type opening that is not letting as much volume get through as the Awesome C-40's yellow Dust Pick up Bowl. I...
by Jason Lacireno
Thu, Mar 14 2013, 9:27AM
Forum: Thermwood 3-Axis Machinery
Topic: Improve Dust Pickup CS43
Replies: 33
Views: 11463

Re: Improve Dust Pickup CS43

I know this is an old post but...

CS-43 Stock dust collector , inefficient , is there another collector i should know about?...just had this machine 2 weeks now.

Or maybe i should make something of my own accord

I still have C-40 that works very well when it comes to (clean-up)

Go to advanced search