I enjoy the new Feature. its a pretty Game changer for me. yeah couple small glitches mentioned here but i still love it.
I've played with this new feature quite a bit and pretty used to it now.
Search found 11 matches
- Tue, Jun 27 2017, 9:03AM
- Forum: Thermwood 3-Axis Machinery
- Topic: the new manual part placement feature
- Replies: 5
- Views: 8853
- Mon, Jan 16 2017, 7:44AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Cut-out instead of pocket
- Replies: 13
- Views: 14642
Re: Cut-out instead of pocket
is it drawn up to cut all the way through or just a pocket? because i'm not sure of any other reason it would do this. write the program. do CTRL+F ...look in the programming to see if it does a (pocket clean up) or (pocket rout). if it does a pocket Rout...then you need to re draw that pocket to cu...
- Mon, Jan 16 2017, 7:30AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Cut-out instead of pocket
- Replies: 13
- Views: 14642
Re: Cut-out instead of pocket
are you using groups?
make sure your changing the setting for the apropriate group.
my cleanup amount is always at 0" ...your settings look fine to me though.
make sure your changing the setting for the apropriate group.
my cleanup amount is always at 0" ...your settings look fine to me though.
- Mon, Aug 15 2016, 7:35AM
- Forum: Thermwood 3-Axis Machinery
- Topic: control upgrade
- Replies: 20
- Views: 66031
Re: control upgrade
We upgraded my C-40 when we bought the CS-43, i think the C-40 over 10 years old
I had windows 2000 on it with weak hardware.
now its upgraded, expensive but affective. nesting time is reduced quite a bit, i wouldnt say cut in half but its much faster.
I had windows 2000 on it with weak hardware.
now its upgraded, expensive but affective. nesting time is reduced quite a bit, i wouldnt say cut in half but its much faster.
- Thu, Jul 07 2016, 6:02AM
- Forum: Thermwood 3-Axis Machinery
- Topic: CS 43 error
- Replies: 3
- Views: 7926
Re: CS 43 error
We Replaced the 24v power supply.
Solved the problem.
I enjoyed the down time while it lasted. Thanks.
Solved the problem.
I enjoyed the down time while it lasted. Thanks.
- Mon, Jul 04 2016, 9:29AM
- Forum: Thermwood 3-Axis Machinery
- Topic: CS 43 error
- Replies: 3
- Views: 7926
Re: CS 43 error
Bumping this thread since i now have the same problem.
The only power i have is the Computer, nothing else.
Thanks.
The only power i have is the Computer, nothing else.
Thanks.
- Mon, Feb 29 2016, 9:59AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Feed Rate Dropping (cs-40)
- Replies: 2
- Views: 6026
Re: Feed Rate Dropping (cs-40)
Thanks for the Reply Carl.
I found a loose white wire with the light blue stripe on the back wall inside the control panel. the screw was almost out completely so i tightenned it up.
I will post a message here by the end of the week with the results.
Hope that was it
thanks again!!!
I found a loose white wire with the light blue stripe on the back wall inside the control panel. the screw was almost out completely so i tightenned it up.
I will post a message here by the end of the week with the results.
Hope that was it
thanks again!!!
- Wed, Feb 17 2016, 10:20AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Feed Rate Dropping (cs-40)
- Replies: 2
- Views: 6026
Feed Rate Dropping (cs-40)
CS-40 computer hardware Gutted and Upgraded to windows 7. After about 2 and a half years of the new upgrade, Feed Rate dropping from 120% to the 90's and 80 percentiles. Changed the adjuster switch and it still does it. I tap the side of the machine and sometimes it jumps back to normal 120% and so...
- Tue, Mar 26 2013, 7:19AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Improve Dust Pickup CS43
- Replies: 38
- Views: 49137
Re: Improve Dust Pickup CS43
This Explains why would be extremely difficult to change Depth of the Bowl...
The tool holders on the C-40 are on stilts wich allow for a deeper grab, unlike the CS-43 wich cant go too far down because of the table...sucks...need try to make the vacuum pathway diameter bigger somehow
The tool holders on the C-40 are on stilts wich allow for a deeper grab, unlike the CS-43 wich cant go too far down because of the table...sucks...need try to make the vacuum pathway diameter bigger somehow
- Thu, Mar 14 2013, 6:19PM
- Forum: Thermwood 3-Axis Machinery
- Topic: Improve Dust Pickup CS43
- Replies: 38
- Views: 49137
Re: Improve Dust Pickup CS43
See...the problem is not Vacuum...the Suction is great when the flex tube is disconnected...its the yellow Bowl itself.... was wrongly made...The bowl itself reduces the diameter, and a slot type opening that is not letting as much volume get through as the Awesome C-40's yellow Dust Pick up Bowl. I...
- Thu, Mar 14 2013, 9:27AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Improve Dust Pickup CS43
- Replies: 38
- Views: 49137
Re: Improve Dust Pickup CS43
I know this is an old post but...
CS-43 Stock dust collector , inefficient , is there another collector i should know about?...just had this machine 2 weeks now.
Or maybe i should make something of my own accord
I still have C-40 that works very well when it comes to (clean-up)
CS-43 Stock dust collector , inefficient , is there another collector i should know about?...just had this machine 2 weeks now.
Or maybe i should make something of my own accord
I still have C-40 that works very well when it comes to (clean-up)