Search found 82 matches

by Geo Noeth
Wed, Sep 24 2008, 5:09AM
Forum: eCabinet Systems Software
Topic: Stagnation?
Replies: 1
Views: 418

Stagnation?

Hi folks, I have not visited the forum for quite a while. I have gotten away from doing kitchens, I have always been a really small one man shop, sometimes two. I have gone to one off furniture pieces and cutting my own parts. This is not necessarily by choice but just because this seems to be what ...
by Geo Noeth
Wed, Jul 02 2008, 1:32PM
Forum: eCabinet Systems Software
Topic: Getting Started in eCabinet Systems
Replies: 3
Views: 572

Re: Getting Started in eCabinet Systems

The best tip I can give you is to take one of Thermwood's classes, You will come out nearly up to full speed.
by Geo Noeth
Thu, Apr 03 2008, 8:58AM
Forum: eCabinet Systems Software
Topic: waterborne lacquer
Replies: 3
Views: 639

Re: waterborne lacquer

Thanks for the comeback Jean, I'll try it. Have you had any problem with it setting up in the gun?
by Geo Noeth
Thu, Apr 03 2008, 4:48AM
Forum: eCabinet Systems Software
Topic: waterborne lacquer
Replies: 3
Views: 639

waterborne lacquer

Campbell finishing systems now makes a product called waterborne lacquer. I was wondering if anyone has tried it. It would make a big difference to those of us who are unable to spray solvent based finishes if it works.
by Geo Noeth
Wed, Dec 12 2007, 12:50PM
Forum: eCabinet Systems Software
Topic: Holy #*&% !!!!!!!
Replies: 34
Views: 4218

I needed some fluted columns for a job a while back. I just drew them up sent the file to Chapman cabinets and received fluted columns when I picked up the parts. Didn't realize it was a big deal. Forrest did you have this problem?
by Geo Noeth
Tue, Dec 04 2007, 1:09PM
Forum: Customer 3D Files
Topic: kitchen table and chairs
Replies: 15
Views: 5244

Joseph,
Use the file in the reply above. one is the table the other is a single chair.

George
by Geo Noeth
Sat, Dec 01 2007, 6:53PM
Forum: eCabinet Systems Software
Topic: hours of operation
Replies: 4
Views: 539

I took the three day course in conjunction with the woodworking show in Vegas. I believe we were told that the material covered was the same, but the practice time was somewhat less. Of course you do not get a tour but we did get show tickets. We did design a cabinet then took it over to the show af...
by Geo Noeth
Mon, Nov 19 2007, 6:41AM
Forum: eCabinet Systems Software
Topic: Program expires
Replies: 3
Views: 521

I'm sure that there are technical reasons that those more knowledgeable than I can explain to you. Here are a couple of reasons that come to mind. The software creates files that are used by their routers to cut parts. For that reason the versions of E-Cabs in the field must be kept current with the...
by Geo Noeth
Sun, Nov 18 2007, 4:01AM
Forum: eCabinet Systems Software
Topic: Ecabs would not start in front of a customer
Replies: 35
Views: 3654

Re:

I sat down with a client today to go over a very importaint job that has been months in the making. I drove an hour each way, I made a big deal out of this meeting, we planed a month in advance, this was a job that I finished designing weeks ago. All this and you did not bother to turn on your PC a...
by Geo Noeth
Sun, Nov 18 2007, 3:47AM
Forum: eCabinet Systems Software
Topic: Ecabs would not start in front of a customer
Replies: 35
Views: 3654

oops
by Geo Noeth
Sat, Nov 17 2007, 6:12AM
Forum: eCabinet Systems Software
Topic: Ecabs would not start in front of a customer
Replies: 35
Views: 3654

Mike, Man that smarts to get embarrassed in front of a customer. The good part of this experience is that will never happen to you again. When you calm down you will realize that this problem was not Thermwood's fault. Every previous version has had an expiration date, and notice was given. The reas...
by Geo Noeth
Thu, Nov 15 2007, 2:44PM
Forum: eCabinet Systems Software
Topic: inset door bead
Replies: 8
Views: 1090

Dan,
Sorry if my original response insulted your ability. I don't know if you just learned anything but I sure did. Best of luck as you get your sea legs with e-cabs.
by Geo Noeth
Thu, Nov 15 2007, 5:14AM
Forum: eCabinet Systems Software
Topic: inset door bead
Replies: 8
Views: 1090

Dan,

The answer to your question is yes. It is done in the part editor. Probably not the first thing I would want to tackle if just beginning to learn the software.
by Geo Noeth
Sun, Nov 04 2007, 5:08AM
Forum: eCabinet Systems Software
Topic: mirrored floor plans
Replies: 1
Views: 370

Denny. I am not aware of any way to do what you are asking. I had a situation where the builder flipped the home floor-plan because of a problem on the lot and didn't tell me until after the cabinets were built. I was surprised at how few changes were necessary I know of a habitat complex where the ...
by Geo Noeth
Thu, Nov 01 2007, 5:50AM
Forum: eCabinet Systems Software
Topic: help with osborne files,still
Replies: 2
Views: 459

David,
When in the display part editor, there is a save button on the left side of the screen next to the load button.

Go to advanced search