Search found 84 matches

by Carmen Addamo
Thu, Aug 09 2018, 4:08PM
Forum: eCabinet Systems Software
Topic: Keeping printer setup
Replies: 1
Views: 66

Keeping printer setup

Everytime I toggle between main view and LDE I have to reset my printer set up specs. Is there anyway to lock these.
by Carmen Addamo
Thu, Aug 09 2018, 4:05PM
Forum: eCabinet Systems Software
Topic: Changing grain direction
Replies: 2
Views: 45

Changing grain direction

Is it possible to change the direction of cabinet backs so if I have a cabinet that is 40" tall and 95" wide I can install the back accordingly so as not to have a seam. I see that I can manipulate the grain direction but doesn't change the width and length specs.
by Carmen Addamo
Mon, Aug 06 2018, 5:49AM
Forum: eCabinet Systems Software
Topic: Create Seam?
Replies: 3
Views: 84

Re: Create Seam?

You can use a stretcher. For example if you have a cabinet that requires a wider/longer back than a piece of sheet stock. Replace the back with two stretchers or give the back an inset that will size it under the max sheet size and add a stretcher for the remaining opening.
by Carmen Addamo
Fri, Jun 08 2018, 3:00PM
Forum: eCabinet Systems Software
Topic: Any way to import pulls
Replies: 1
Views: 156

Any way to import pulls

The "pulls" library from ecabs is really dated. Would really like to display some modern 6/8/12" contemporary pulls. Anyway to achieve this?
by Carmen Addamo
Thu, Apr 19 2018, 11:07AM
Forum: eCabinet Systems Software
Topic: Suggestions on how to drill three sets of shelf pin holes
Replies: 9
Views: 542

Re: Suggestions on how to drill three sets of shelf pin holes

There is a setting for adding a center row under Add Shelf settings using the apply shelf hole settings Yes, but I don't believe you can specify the location from the front or back edge. It only palces the holes centered between the front and rear holes. I also don't know what the "single row ...
by Carmen Addamo
Tue, Apr 17 2018, 6:12PM
Forum: eCabinet Systems Software
Topic: Suggestions on how to drill three sets of shelf pin holes
Replies: 9
Views: 542

Suggestions on how to drill three sets of shelf pin holes

Closet project where it is necessary to drill three rows of holes. How do i set up for the center row (for adjustable hanging rod) at a specific distance from the front (or it could be referenced from the back) edge. I would also like to drill uprights that do not actualy contain adjustable shelves....
by Carmen Addamo
Sat, Apr 14 2018, 6:36AM
Forum: eCabinet Systems Software
Topic: Issue updating to 6.2.1
Replies: 3
Views: 490

Re: Issue updating to 6.2.1

Scott I had no issues updating. You could try turning off your firewall.
by Carmen Addamo
Wed, Mar 28 2018, 9:02PM
Forum: eCabinet Systems Software
Topic: Notes in Line Editor
Replies: 1
Views: 358

Re: Notes in Line Editor

Yes, same issue here
by Carmen Addamo
Thu, Feb 08 2018, 10:32PM
Forum: eCabinet Systems Software
Topic: Ok, stupid question....
Replies: 4
Views: 689

Re: Ok, stupid question....

Yes, as tim said, you must associate all display parts to a cabinet. Click on and highlight the display part. Double click on the cabinet. Right click to access the drop down menu and click on associate to cabinet.
by Carmen Addamo
Mon, Feb 05 2018, 10:10AM
Forum: eCabinet Systems Software
Topic: Any way to edit dimensions
Replies: 3
Views: 798

Re: Any way to edit dimensions

Thanks Scott. I'll start experimenting with workarounds.
by Carmen Addamo
Sat, Feb 03 2018, 6:33AM
Forum: eCabinet Systems Software
Topic: Any way to edit dimensions
Replies: 3
Views: 798

Any way to edit dimensions

Any one know if there is some way to overwrite a dimension. I am attempting to avoid having to take the same basic cabinet into LDE for every new job. What I did was create a job out of each individual cabinet in a library. When I pull up the job, drawer base, for example, the shop drawings is alrea...
by Carmen Addamo
Mon, Jan 08 2018, 7:45PM
Forum: eCabinet Systems Software
Topic: Purpose of locked openings
Replies: 7
Views: 987

Re: Purpose of locked openings

Okay Thanks Clint. The cabinet I posted was from Ecabs. My question was that I didn't know how to import posted cabinets from this forum into ecabs as a cabinet that could be edited or just simply viewed as any other cabinet that was originally constructed within ecabs. For example the cabinet I pos...
by Carmen Addamo
Fri, Jan 05 2018, 1:06PM
Forum: eCabinet Systems Software
Topic: Purpose of locked openings
Replies: 7
Views: 987

Re: Purpose of locked openings

While I have your attention would you mind explaining how one goes about importing this hsf file into ecabinets so it can be handled as a cabinet. I know how to import from display part editior but that turns my file into a dispaly part. Yes I'm clueless :?
by Carmen Addamo
Fri, Jan 05 2018, 12:30PM
Forum: eCabinet Systems Software
Topic: Purpose of locked openings
Replies: 7
Views: 987

Re: Purpose of locked openings

Scott I deleted the cabinet yesterday and replaced the partitions with stretchers. Today I used the seed base cabinet from the "Standard Library" and replicated the partitions I was having issues with and all was working fine with opening widths remaining locked upon resizing. So I now cha...

Go to advanced search