Search found 2692 matches

by Kerry Fullington
Wed, Mar 20 2019, 11:57AM
Forum: eCabinet Systems Software
Topic: Shelf Standards or pilasters
Replies: 8
Views: 155

Re: Shelf Standards or pilasters

Stuart, In the hardware hole editor I am not sure the lines are actual X and Y Axis. As for my shelf, the pattern is drawn centered on what would be the x axis and runs left of what would be the y axis. This placed the cut on the end of the cabinet centered where my kd fitting would be. If I draw it...
by Kerry Fullington
Wed, Mar 20 2019, 6:31AM
Forum: eCabinet Systems Software
Topic: Shelf Standards or pilasters
Replies: 8
Views: 155

Re: Shelf Standards or pilasters

Stuart, I did this in the past with a hardware pattern as you mentioned KV Standard.jpg The only problem was I had to apply a different hole pattern (for length) for base cabinets, tall cabinets and upper cabinets as well as different lengths for different heights of uppers. For a one off it is just...
by Kerry Fullington
Sun, Mar 03 2019, 9:45AM
Forum: eCabinet Systems Software
Topic: RELIEF HELP ME
Replies: 7
Views: 315

Re: RELIEF HELP ME

Ismet,

It would help if you had a better image of the logo. The best would be an image in the .eps format. (encapsulated post script)
This will help to have clean edges to detect and create a .dxf.
The edges are too ragged from your small image
ecocab cut.JPG
by Kerry Fullington
Fri, Mar 01 2019, 1:01PM
Forum: eCabinet Systems Software
Topic: Hp Printers - No leaders
Replies: 8
Views: 342

Re: Hp Printers - No leaders

Terry,

I installed the HP Universal Print Driver for Windows PCL6 (64-bit) for my printer from the HP site this morning and it fixed my leader printing problem.
by Kerry Fullington
Sat, Feb 16 2019, 10:51AM
Forum: eCabinet Systems Software
Topic: Crash in line drawing
Replies: 6
Views: 309

Re: Crash in line drawing

Tom, I have had this problem in the past on different occasions. It always seemed to happen after a Windows Update and updating printer drivers was the solution. Do you have another printer available to set as default in eCabinets and see if that helps. It might give some insight on if it is a print...
by Kerry Fullington
Fri, Feb 15 2019, 10:14AM
Forum: eCabinet Systems Software
Topic: User Defined Operations
Replies: 4
Views: 246

Re: User Defined Operations

Thanks Clint,

I found them earlier this morning.
by Kerry Fullington
Thu, Feb 14 2019, 8:03PM
Forum: eCabinet Systems Software
Topic: Design Sharing similar to Production Sharing?
Replies: 5
Views: 2105

Re: Design Sharing similar to Production Sharing?

Hey Tom,

The eCab store was something I was playing around with a couple of years ago but never did follow through with it.
I should probably take the link down.
I have lots of stuff but getting it tested and presentable for the store as well as addressing liability concerns got to be a lot of work.
by Kerry Fullington
Thu, Feb 14 2019, 8:00PM
Forum: eCabinet Systems Software
Topic: User Defined Operations
Replies: 4
Views: 246

Re: User Defined Operations

Hey Scott,

Good to hear from you.

I remember those links but couldn't find them again. I browsed through the videos on the training site but didn't see anything there either.
I have looked at the help links in the software but they just confuse me.
by Kerry Fullington
Thu, Feb 14 2019, 1:53PM
Forum: eCabinet Systems Software
Topic: User Defined Operations
Replies: 4
Views: 246

User Defined Operations

Where can I learn about User Defined Operations.
by Kerry Fullington
Thu, Feb 07 2019, 12:46PM
Forum: eCabinet Systems Software
Topic: corner cabinet toe kick
Replies: 4
Views: 212

Re: corner cabinet toe kick

Joe,
I opened your cabinet in the cab editor and then went to Construction Settings/Toe Kick tab and exited without changing anything and this is what I got.

Clipboard01.jpg
by Kerry Fullington
Mon, Jan 21 2019, 6:33PM
Forum: eCabinet Systems Software
Topic: Measure
Replies: 2
Views: 249

Re: Measure

Tim, Take the Standard Base Frameless and delete all the parts except the back. I changed the back to a Do Not Cut material Make the cabinet 3/4" wide and 3/4" Deep I make my cabinet 42" tall so it will show through cabinets. Save this as 3/4 Pipe (you can create a 1" material or...
by Kerry Fullington
Tue, Jan 01 2019, 11:09AM
Forum: eCabinet Systems Software
Topic: Louvered Door Tooling
Replies: 2
Views: 395

Re: Louvered Door Tooling

Hey Justin, To I created the sawtooth tool geometry in Auto Cad, (you can do it in eCabs if you want) similar to what Scott has in his video Louver 1.jpg then I just profiled slots in the back to open it for ventilation. Louver 2.jpg It still isn't a great louvered door because the louvers don't ove...
by Kerry Fullington
Mon, Nov 26 2018, 12:35PM
Forum: eCabinet Systems Software
Topic: Shop Drawings
Replies: 4
Views: 757

Re: Shop Drawings

Thanks All,

I have been away from eCabinets and manufacturing for a couple of years and it is nice to be back.
Still looking for the button that automatically prints all shop drawings. :D
by Kerry Fullington
Sun, Nov 25 2018, 2:01PM
Forum: eCabinet Systems Software
Topic: Shop Drawings
Replies: 4
Views: 757

Shop Drawings

I am still looking for a better way to create shop and installation drawings as per This Thread from 2016.
Any Ideas?
by Kerry Fullington
Sun, Nov 25 2018, 1:50PM
Forum: eCabinet Systems Software
Topic: Notes
Replies: 0
Views: 623

Notes

How does everyone make notes in Custom Layout? Right now I open OneNote and toggle back an forth. I know I can take the layout into the Line Editor and make notes there but because the Line Drawing Editor is not dynamic it doesn't work very well. It also takes too much time. I talked to Scott Vaal m...

Go to advanced search