Search found 315 matches

by Clint Buechlein
Wed, Aug 21 2019, 12:00PM
Forum: Thermwood 3-Axis Machinery
Topic: Where is my table, in relation to Z0 home? CS-45
Replies: 1
Views: 15

Re: Where is my table, in relation to Z0 home? CS-45

Richard, Most likely you are correct in the table heights being different. Before I can offer advice on getting it set up properly, can you post one of your programs you are attempting to run or email it to program@thermwood.com? Also, does this machine have a tool sensor on it for measuring dayligh...
by Clint Buechlein
Tue, Aug 20 2019, 3:09PM
Forum: eCabinet Systems Software
Topic: Kinda off the subject of eCabs - TWD CNC machines
Replies: 15
Views: 207

Re: Kinda off the subject of eCabs - TWD CNC machines

The only need need air for on the machine is tool changes, placement pins, and vacuum valve to apply vacuum to the table as Jeremy said. Placement pins and vacuum valve do not require much air. Optionally you can have air assist which blows air under the boards to make loading and unloading heavier ...
by Clint Buechlein
Fri, Aug 16 2019, 9:12AM
Forum: Thermwood 3-Axis Machinery
Topic: THM not starting
Replies: 9
Views: 99

Re: THM not starting

Next step then would be to make sure the memory stick(s) are seated properly in the motherboard. Same process, remove,make sure there isn't anything in the way and seat back in. Also check to make sure if there are multiple sticks that the amount of memory available for the system is accurate to how...
by Clint Buechlein
Thu, Aug 15 2019, 3:25PM
Forum: eCabinet Systems Software
Topic: Roughing button missing in CN 6.14
Replies: 9
Views: 131

Re: Roughing button missing in CN 6.14

Understandable, especially from the cost aspect. If you aren't behind in work or turning it away it would be hard to justify buying a new machine. With your 45, you should be seeing feed speeds of 650ipm or so (should be fair bit faster than your 41), so hopefully you're seeing faster processing tim...
by Clint Buechlein
Thu, Aug 15 2019, 3:05PM
Forum: eCabinet Systems Software
Topic: Desktop Software & Time Study
Replies: 6
Views: 94

Re: Desktop Software & Time Study

Troy, The easiest way to get your office computer set up to match your machine would be to run THMsync. This is available on your desktop version on the C drive in the System Folder. Move the THMsync.exe to a flash drive or put it on a network location you can get to from the machine. Run the sync a...
by Clint Buechlein
Thu, Aug 15 2019, 2:24PM
Forum: Thermwood 3-Axis Machinery
Topic: THM not starting
Replies: 9
Views: 99

Re: THM not starting

Tommy, Power down the machine, pull off the side cabinet and take a look at the card cage. There is a purple cable running to the bottom of the card cage into a card that is plugged into the mother board. With the machine powered down, unseat that card from the motherboard, and reseat it. Also make ...
by Clint Buechlein
Thu, Aug 15 2019, 1:29PM
Forum: eCabinet Systems Software
Topic: Desktop Software & Time Study
Replies: 6
Views: 94

Re: Desktop Software & Time Study

Troy,

What is the THM software version on your machine and on the desktop version of the software?

-Clint-
by Clint Buechlein
Wed, Aug 14 2019, 3:22PM
Forum: eCabinet Systems Software
Topic: Roughing button missing in CN 6.14
Replies: 9
Views: 131

Re: Roughing button missing in CN 6.14

Tough question there. Are you running similar speeds on your 45 as you are on your 41? The 45 you should be running quite a bit faster than the 41. Unless you have a full need for what the 45 has to offer, you could go to a 43 instead. Save a little bit of money that route. On the other hand, if you...
by Clint Buechlein
Wed, Aug 14 2019, 12:42PM
Forum: eCabinet Systems Software
Topic: Roughing button missing in CN 6.14
Replies: 9
Views: 131

Re: Roughing button missing in CN 6.14

Jeremy, Unfortunately your machine must be version 7.6 or newer for the roughing feature. There was not the necessary AFL code that is required for the roughing to work prior to 7.6. The Control Nesting update page should be updated now to reflect that. On the other side of things, be a good time to...
by Clint Buechlein
Wed, Aug 14 2019, 11:53AM
Forum: eCabinet Systems Software
Topic: Kinda off the subject of eCabs - TWD CNC machines
Replies: 15
Views: 207

Re: Kinda off the subject of eCabs - TWD CNC machines

Don, I'll answer what I can and let other uses chime in with their own particular experience: 1. All our machines are production machines. We have users from factories to small buildings with the machines running three shifts to being used a few times a month. 2. What you use in the ShopBot link is ...
by Clint Buechlein
Tue, Jul 23 2019, 3:42PM
Forum: Thermwood 5-Axis Machinery
Topic: Ice Qube not working
Replies: 3
Views: 169

Re: Ice Qube not working

Yippee! It was just the fuse. Don't know why I didn't check that first - it was clearly labeled. Thanks for you help :D Good to hear it was simple. Make sure filter and coils are clean so it isn't overdrawing itself. And keep an eye on it in the event something on the inside of the a/c unit is goin...
by Clint Buechlein
Tue, Jul 23 2019, 7:57AM
Forum: Thermwood 5-Axis Machinery
Topic: Ice Qube not working
Replies: 3
Views: 169

Re: Ice Qube not working

Eric, Open up the side of the cabinet and trace the wires back to their junction. You can use a multimeter to verify you have voltage there, should be normal 110 AC so don't shock yourself. If you don't have voltage there trace it back to see if the fuse is blown. If you do have voltage there, you c...
by Clint Buechlein
Wed, Jul 10 2019, 9:00AM
Forum: eCabinet Systems Software
Topic: Colored symbols on labels
Replies: 62
Views: 4608

Re: Colored symbols on labels

What was messed up about them? First job in the nest, all cab numbers are correct. Second job in the nest, cabinet numbers carry on from where they left off in the first job. So if the first job has 30 cabinets for example, Cabinet one in the second job will be labeled 31. However, the "origin...
by Clint Buechlein
Tue, Jul 09 2019, 8:18AM
Forum: eCabinet Systems Software
Topic: Colored symbols on labels
Replies: 62
Views: 4608

Re: Colored symbols on labels

Tommy Wieler wrote:Try nesting and cutting multiple jobs simultaneously. The large cabinet numbers get messed up.


I should be able to nudge the barcode and barcode ID up a little.

Tommy Wieler wrote:Try nesting and cutting multiple jobs simultaneously. The large cabinet numbers get messed up.


What was messed up about them?

-Clint-
by Clint Buechlein
Fri, Jul 05 2019, 10:27AM
Forum: eCabinet Systems Software
Topic: Colored symbols on labels
Replies: 62
Views: 4608

Re: Colored symbols on labels

Someone can give this recut one a go if they use the barcode scanner. I made the barcode a little taller from the standard also.

-Clint-

Go to advanced search