I'm seeing the same thing here. We will get it listed, thank you.
-Clint-
Search found 175 matches
- Wed, Apr 18 2018, 7:32AM
- Forum: Thermwood 3-Axis Machinery
- Topic: priorities glitch
- Replies: 1
- Views: 43
- Wed, Apr 18 2018, 7:26AM
- Forum: eCabinet Systems Software
- Topic: Suggestions on how to drill three sets of shelf pin holes
- Replies: 8
- Views: 137
Re: Suggestions on how to drill three sets of shelf pin holes
Closet project where it is necessary to drill three rows of holes. How do i set up for the center row (for adjustable hanging rod) at a specific distance from the front (or it could be referenced from the back) edge. I would also like to drill uprights that do not actualy contain adjustable shelves...
- Mon, Apr 16 2018, 8:44AM
- Forum: eCabinet Systems Software
- Topic: Can't open current file after upgrade to 6.2.1
- Replies: 2
- Views: 77
- Wed, Apr 04 2018, 1:09PM
- Forum: eCabinet Systems Software
- Topic: Dovetail drawer depth not resizing properly
- Replies: 3
- Views: 248
Re: Dovetail drawer depth not resizing properly
Forrest, I looked at it for a few minutes yesterday then got wrapped up in other stuff. The first time I resized it, I had the same issue you did. At least close to what you did. My display size was wrong versus actual measured and inputted size, but the numbers weren't the same. I had seen an issue...
- Wed, Apr 04 2018, 7:20AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Aspire export/import
- Replies: 10
- Views: 358
Re: Aspire export/import
Thanks for that Clint. I haven't tried any code editing yet. In fact, I was trying to steer away from even opening that book. But that is good advice because I was thinking I would be able to do it in the machine controller. Thanking you Mark You can edit the code at the controller, but the ideal s...
- Tue, Apr 03 2018, 7:41AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Aspire export/import
- Replies: 10
- Views: 358
Re: Aspire export/import
Also as a note the posts for Aspire can be edited in Notepad. There are relatively easy to understand once you look at some code you've posted. Just be sure to make a copy of the post before you edit it in the event you break it too badly
.
-Clint-

-Clint-
- Mon, Apr 02 2018, 9:17AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Aspire export/import
- Replies: 10
- Views: 358
Re: Aspire export/import
Everything Dave said and a little more information. The post will be close for your machine, but it will get hung up at the beginning if you don't adjust the pop up pin output number. And remove the input call for pop up pins. Also there is no ZSHIFT in that post so you'll have to choose Machine Bed...
- Tue, Mar 20 2018, 7:54AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Drill Hole Issues
- Replies: 5
- Views: 343
Re: Drill Hole Issues
Rachel, For your first question regarding the 5mm drill, make sure the 5mm drill is in the operation list before the 3.18 mm cutter. In general your tools should be ordered from largest to smallest. Control Nesting starts at operation 1 in Tooling and checks to operation 50. As soon as the Control N...
- Fri, Mar 16 2018, 8:01AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Machining plam on 1 1/2'' thick pressboard
- Replies: 2
- Views: 180
Re: Machining plam on 1 1/2'' thick pressboard
As you read the response below, keep in mind I don't do a lot of cutting. I do some, but not nearly enough to be considered "production". My initial thought is the 250-300 ipm is too slow for a 1/2" bit. Going by Onsrud's chip load calculator located here http://www.onsrud.com/files/p...
- Thu, Mar 15 2018, 2:32PM
- Forum: Lounge
- Topic: Duplicating cabinets for better nesting.
- Replies: 2
- Views: 469
- Thu, Mar 15 2018, 2:26PM
- Forum: eCabinet Systems Software
- Topic: Backup my libary ?
- Replies: 7
- Views: 386
Re: Backup my libary ?
Do you happen to know if this includes the librarys i have made and downloaded ? or do i save those in another way? Thanks again i love this fourm and eCabs! It should. The Jobs, Tools, and Drawer Boxes can all be stored somewhere other than default so you have the option to set the location where ...
- Thu, Mar 15 2018, 7:34AM
- Forum: eCabinet Systems Software
- Topic: Duplicating cabinets for better nesting.
- Replies: 4
- Views: 327
Re: Duplicating cabinets for better nesting.
Hi all, I am making seven kitchenettes and have created one of them (which comprises of three cabinets and a benctop). Is there any way that I can multiply that kitchenette by seven to get better nesting and less waste, or do I have to create it seven times in the same room to do so? Thanks--Mick. ...
- Wed, Mar 14 2018, 12:38PM
- Forum: eCabinet Systems Software
- Topic: How to get version 6.2
- Replies: 9
- Views: 391
Re: How to get version 6.2
Andy, There shouldn't be any issues losing files or settings. If you haven't lately (or ever) taken a backup from eCabinets, I highly highly highly suggest you do. The backup will grab important files and settings in the event of a hard drive failure. I highly recommend creating the back up and stor...
- Wed, Mar 14 2018, 7:25AM
- Forum: eCabinet Systems Software
- Topic: How to get version 6.2
- Replies: 9
- Views: 391
Re: How to get version 6.2
That is very possible. Most of the time my internet is amazing but today its really bad. I tried looking for the files to try them again and could not find them in that folder. do you have any suggestions on how to proceed from here? You'll have to start the download again. The download most likely...
- Wed, Mar 14 2018, 7:22AM
- Forum: Thermwood 3-Axis Machinery
- Topic: Print Engine Error
- Replies: 7
- Views: 247
Re: Print Engine Error
Just out of curiosity I tried the export option at the machine and the desktop version. Both display the error. Never use export but there does seem to be a problem there. We are aware of the issue, just haven't made it there. The export option is Window's way of creating a PDF. There are other opt...