Search found 79 matches

by Tommy Wieler
Tue, Jun 23 2020, 8:45AM
Forum: Thermwood 3-Axis Machinery
Topic: Default Flycut Values
Replies: 6
Views: 324

Re: Default Flycut Values

Thanks a lot Cliff! Exactly what I wanted...
Have a great day!
by Tommy Wieler
Mon, Jun 22 2020, 9:20AM
Forum: Thermwood 3-Axis Machinery
Topic: Default Flycut Values
Replies: 6
Views: 324

Re: Default Flycut Values

Sorry I've been away from the shop for a couple weeks. Here's the file, looking forward to what you've got for me!
Thanks Clint!
by Tommy Wieler
Mon, Jun 08 2020, 12:44PM
Forum: Thermwood 3-Axis Machinery
Topic: Default Flycut Values
Replies: 6
Views: 324

Re: Default Flycut Values

Thanks Clint. I know we're a little odd cause we use metric by default in our shop, so I would like to get a nice round number for the flycut, like 0.3mm instead of 0.254mm.
by Tommy Wieler
Thu, Jun 04 2020, 1:46PM
Forum: Thermwood 3-Axis Machinery
Topic: Default Flycut Values
Replies: 6
Views: 324

Default Flycut Values

I was just wondering if there is a way to change the default amount that gets removed from the wasteboard during a flycut?
by Tommy Wieler
Fri, May 29 2020, 8:48AM
Forum: eCabinet Systems Software
Topic: Profile modeler
Replies: 17
Views: 735

Re: Profile modeler

Maybe it has to do with the profile touching the bottom of the pocket

Maybe you could try drawing the model so it stops .2mm off the bottom of the pocket, then just add .2mm to the daylight value of the modelling tool at the machine.
by Tommy Wieler
Tue, Apr 21 2020, 11:07AM
Forum: Thermwood 3-Axis Machinery
Topic: Sheet Yield affected by voids
Replies: 1
Views: 609

Sheet Yield affected by voids

Greetings again.
Just a heads up: sheet yield numbers become inaccurate when adding a voided area on a sheet, as shown in example below
Capture12.JPG
by Tommy Wieler
Mon, Apr 20 2020, 2:30PM
Forum: Thermwood 3-Axis Machinery
Topic: Program Timer Idea
Replies: 3
Views: 820

Re: Program Timer Idea

That's fantastic, thanks Clint! Is there any way to change the feed rate that is used to calculate the sheet times in this report?
by Tommy Wieler
Fri, Apr 17 2020, 11:11AM
Forum: Thermwood 3-Axis Machinery
Topic: Program Timer Idea
Replies: 3
Views: 820

Program Timer Idea

Greetings all! I had an idea on how the program timer could be developed further... I would love to be able to request an estimated run time for a particular sheet in a job. Right now it's giving me the total run time for the entire job. Often, when we're running complex modelled doors, we do those ...
by Tommy Wieler
Wed, Apr 08 2020, 9:00AM
Forum: Thermwood 3-Axis Machinery
Topic: Manual nesting offals
Replies: 1
Views: 818

Manual nesting offals

Here's something that crops up quite often when I'm using manual nesting to move parts around. In the attached example, I've moved a few of the smaller parts to give them some additional part clearance to ensure that they don't move during cutting. For some reason, offal shapes get calculated differ...
by Tommy Wieler
Mon, Mar 30 2020, 10:41AM
Forum: Lounge
Topic: What methods do you use to hold down small parts?
Replies: 5
Views: 2439

Re: What methods do you use to hold down small parts?

Our favorite method is to use additional part clearance, and leave a skin before final outline, although I plead guilty to adhesive and nails as well. But hands? Really?? Not sure I have the guts to hold down a small part by hand with a router bit spinning at 20000RPM within a few inches of my hand.
by Tommy Wieler
Fri, Mar 13 2020, 12:31PM
Forum: Thermwood 3-Axis Machinery
Topic: Ramp-in location
Replies: 0
Views: 2267

Ramp-in location

Greetings all! Is there any way to change how the machine does ramp-ins? Currently the bit starts at a corner of the piece, then ramps in, cuts the outline, then finishes the outline up to the end of the rampin. This means that the bit gets pulled out of the material partially along an edge, leaving...
by Tommy Wieler
Fri, Jan 17 2020, 10:15AM
Forum: Thermwood 3-Axis Machinery
Topic: Modelling partially broken?
Replies: 4
Views: 1938

Re: Modelling partially broken?

Never mind... :oops: another case of an issue not being thoroughly researched before reporting it. Disregard this thread... my foot is firmly planted in my mouth, and I'm not particularly enjoying the flavor...
by Tommy Wieler
Fri, Jan 17 2020, 9:46AM
Forum: Thermwood 3-Axis Machinery
Topic: Modelling partially broken?
Replies: 4
Views: 1938

Re: Modelling partially broken?

I can confirm this morning that it is the latest update to Profile Modeler that has caused the issue for us. I rolled back to v2.6, and the model turns out perfect.
by Tommy Wieler
Thu, Jan 16 2020, 4:31PM
Forum: Thermwood 3-Axis Machinery
Topic: Modelling partially broken?
Replies: 4
Views: 1938

Modelling partially broken?

Greetings all. Please see attached pictures. We're trying to model a 45 degree bevel on the inside of a door panel, which used to work just fine. But the exact same model that used to work is now not giving us the results we want. Seems like the ballnose bit doesn't finish the job properly, leaving ...

Go to advanced search