Search found 46 matches

by Sean O' Hare
Fri, Aug 09 2013, 3:37AM
Forum: eCabinet Systems Software
Topic: Rebates with lip cutouts
Replies: 7
Views: 1610

Re: Rebates with lip cutouts

Jason,

when I need a rebate beside a cut-out, I offset it .1mm. That way, the machine cuts them separately with the standard tools.

Sean
by Sean O' Hare
Fri, Nov 09 2012, 6:57AM
Forum: Thermwood 3-Axis Machinery
Topic: Improve Dust Pickup CS43
Replies: 33
Views: 11762

Re: Improve Dust Pickup CS43

Kerry, looking at your pile of dust on the floor, I built a tray 4ft long & 12" wide/deep with 1 long open side facing the table. It sits alongside the table just below the home position of the router. When I blow off the table I do it towards the tray, & the extractor pulls it out.
by Sean O' Hare
Fri, Apr 06 2012, 4:32AM
Forum: eCabinet Systems Software
Topic: How do I rabbit around an opening after a cutout?
Replies: 9
Views: 2414

Re: How do I rabbit around an opening after a cutout?

Steve,
offset the shallow cut out by a fraction, .1mm so that the software sees them as 2 separate cuts.
by Sean O' Hare
Mon, Mar 19 2012, 4:19AM
Forum: Thermwood 3-Axis Machinery
Topic: Pocketing Problem
Replies: 12
Views: 2134

Re: Pocketing Problem

I hope you got it cut , Kerry. What I do there is make the thro cut as 1 pocket, then offset the rebate .1mm out from it. Works fine.
by Sean O' Hare
Sat, Mar 03 2012, 7:42AM
Forum: Thermwood 3-Axis Machinery
Topic: Drawbar up switch has not opened
Replies: 5
Views: 1259

Re: Drawbar up switch has not opened

Thanks for the replies. I've had low air/no air in the past, & a toolholder sticking. This time it would release the tool but not make the final push that seats it in the rack. With tech help, we established that S1 was faulty, it inputs as s2 on the F6/F3 screen & was constantly on, inc. wh...
by Sean O' Hare
Wed, Feb 29 2012, 7:42AM
Forum: Thermwood 3-Axis Machinery
Topic: Drawbar up switch has not opened
Replies: 5
Views: 1259

Re: Drawbar up switch has not opened

Thanks, Forrest.

No, it seems to be a faulty sensor.
by Sean O' Hare
Tue, Feb 28 2012, 10:59AM
Forum: Thermwood 3-Axis Machinery
Topic: Drawbar up switch has not opened
Replies: 5
Views: 1259

Drawbar up switch has not opened

Hello,

I'm getting this error message on our model 40. Any help would be appreciated.

Thanks
by Sean O' Hare
Fri, Feb 04 2011, 11:31AM
Forum: Thermwood 3-Axis Machinery
Topic: Problem cutting pocket
Replies: 4
Views: 830

Re: Problem cutting pocket

Ryan,

that works perfectly. Thanks for the prompt response.
by Sean O' Hare
Mon, Jan 31 2011, 12:40PM
Forum: Thermwood 3-Axis Machinery
Topic: Problem cutting pocket
Replies: 4
Views: 830

Problem cutting pocket

Hello,

I'm getting a strange result when I cut the pocket in the frame handle for this job. Anyone have any ideas?

Thanks
by Sean O' Hare
Mon, Jan 31 2011, 12:32PM
Forum: eCabinet Systems Software
Topic: Problem with the PE causing Ecabs to close
Replies: 9
Views: 904

Re: Problem with the PE causing Ecabs to close

Scott,
fyi, uninstall/reinstall solved the problem.

Thanks
by Sean O' Hare
Thu, Jan 20 2011, 7:15AM
Forum: eCabinet Systems Software
Topic: Problem with the PE causing Ecabs to close
Replies: 9
Views: 904

Re: Problem with the PE causing Ecabs to close

Scott,

Faulting applications ecabinets.exe. version 6.0.57.0. faulting module ecabinets.exe. version 6.0.57.0. fault address 0x00f6cb4e.

I've updated the driver, but no change.
Should I remove & reinstall ecabs? If so, what files do I need to save to avoid losing existing jobs?

Thank you,
by Sean O' Hare
Wed, Jan 19 2011, 6:21AM
Forum: eCabinet Systems Software
Topic: Problem with the PE causing Ecabs to close
Replies: 9
Views: 904

Re: Problem with the PE causing Ecabs to close

Scott, this is what I get. It also closes if I try to alter a stretcher. 0000: 41 70 70 6c 69 63 61 74 Applicat 0008: 69 6f 6e 20 46 61 69 6c ion Fail 0010: 75 72 65 20 20 65 63 61 ure eca 0018: 62 69 6e 65 74 73 2e 65 binets.e 0020: 78 65 20 36 2e 30 2e 35 xe 6.0.5 0028: 37 2e 30 20 69 6e 20 65 7.0...
by Sean O' Hare
Tue, Jan 18 2011, 4:02AM
Forum: eCabinet Systems Software
Topic: edit wall cutouts
Replies: 3
Views: 735

Re: edit wall cutouts

Patrick,

in Edit Wall view, select create rectangle from the drop down. In the Enter Start Point, enter horizontal dim, vertical dim & press enter. Repeat for end point.
by Sean O' Hare
Wed, Jan 12 2011, 10:12AM
Forum: eCabinet Systems Software
Topic: Problem with the PE causing Ecabs to close
Replies: 9
Views: 904

Re: Problem with the PE causing Ecabs to close

Scott,

it loads ok but closes if I try to adjust the cabinet. I've attached a simple 1 (I hope). System is Windows XP.

Thanks
by Sean O' Hare
Tue, Jan 11 2011, 12:58PM
Forum: eCabinet Systems Software
Topic: Problem with the PE causing Ecabs to close
Replies: 9
Views: 904

Problem with the PE causing Ecabs to close

I've started having a problem with Ecabs closing every time I try to use a cabinet with PE cuts applied. Cabinets I've used before now cause the program to crash. I can create a new cabinet & apply cuts, but if I try to change anything afterwards it closes. Nothing on my system has changed excep...

Go to advanced search