Search found 140 matches

by Brian Bauer
Wed, May 27 2015, 11:02PM
Forum: eCabinet Systems Software
Topic: need a new key code for reinstall
Replies: 1
Views: 679

need a new key code for reinstall

Hi I could use a new key code to reinstall ecabs on new computer, but I have since changed email addresses. New email is bbauer71@yahoo.com. Thanks in advance Brian Bauer
by Brian Bauer
Wed, Sep 24 2008, 5:43PM
Forum: eCabinet Systems Software
Topic: door settings question.
Replies: 1
Views: 343

Re: door settings question.

Nevermind, the mdf with cutters works great, would be more helpful if the cutters were labeled as to what they were instead of having to look at each one.

Brian
by Brian Bauer
Wed, Sep 24 2008, 4:43PM
Forum: eCabinet Systems Software
Topic: door settings question.
Replies: 1
Views: 343

door settings question.

Hello All , I have a quick question about door settings , which drawer front style would i have to pick to get a vertical grain drawer front, that is roughly 7 inches tall and 36" wide I keep getting an error message saying if I exceed on dimension i have to blah blah blah. I just did a job in ...
by Brian Bauer
Tue, Jul 08 2008, 3:47PM
Forum: eCabinet Systems Software
Topic: Problems saving in the LDE
Replies: 1
Views: 290

Problems saving in the LDE

Why would ecabs all of a sudden stop saving properly? It has been working great then just decided it doesn't want to save anymore. any ideas? This would be in the LDE. I would bang my head against the wall but it's too hot i'd probably burn it badly first. :roll:

Any ideas?

Thanks Brian
by Brian Bauer
Tue, Jun 24 2008, 7:20PM
Forum: eCabinet Systems Software
Topic: captive backs
Replies: 2
Views: 446

Re: captive backs

Thanks Jerry,

I knew it was something little. Gotta stand back and get a good look sometimes. Focusing on the details too much. :beer:

Brian
by Brian Bauer
Tue, Jun 24 2008, 6:18PM
Forum: eCabinet Systems Software
Topic: captive backs
Replies: 2
Views: 446

captive backs

Captive backs, I have been sitting here messing around trying to get a 1/2" back held captive in a 3/8" dado,set in from the back edge of the cabinet 3/4 of an inch But when i go to the back screen to fill out the joint info it has the top blocked out. Am I missing something somwhere else....
by Brian Bauer
Tue, Jun 24 2008, 1:36PM
Forum: eCabinet Systems Software
Topic: LDE question
Replies: 2
Views: 395

Re: LDE question

Thanks Todd, I knew it was too easy :P
Brian
by Brian Bauer
Tue, Jun 24 2008, 1:08PM
Forum: eCabinet Systems Software
Topic: LDE question
Replies: 2
Views: 395

LDE question

Hello all.

hopefully an easy question. How do you change the orientation of the page in the LDE from vertical to horizontal?

Thanks Brian
by Brian Bauer
Wed, May 07 2008, 1:32PM
Forum: eCabinet Systems Software
Topic: Placing lights
Replies: 2
Views: 399

Re: Placing lights

Thanks Kerry,
I figured it out right after I posted, But it is nice to know where the heght adjustment is also. I only found it by accident. I was looking for a dialogue box to check and saw that they were hidden :oops: .
Guess trying to design under the gun probably ain't the way to go.

Brian
by Brian Bauer
Wed, May 07 2008, 12:57PM
Forum: eCabinet Systems Software
Topic: Placing lights
Replies: 2
Views: 399

Placing lights

While placing lights, I place them where i need them then hit esc to get rid of the light that i'm placing and it gets rid of all the lights i just placed,Is there something new I need to be aware of?
Also where is the set height input screen located at? for the lights.
Brian
by Brian Bauer
Sat, May 03 2008, 12:15PM
Forum: eCabinet Systems Software
Topic: Need an angled lower!
Replies: 26
Views: 2289

Re: Need an angled lower!

Damon I was a few months into the planning of this job when I was informed that the "theme" of this job was a stealth fighter crashed into the side of a hill. The whole job has pretty much followed suit :roll: But in the interest of making money,What the hell. Gotta have something to tell ...
by Brian Bauer
Sat, May 03 2008, 1:17AM
Forum: eCabinet Systems Software
Topic: Need an angled lower!
Replies: 26
Views: 2289

Re: Need an angled lower!

Damon yes that is what I was looking for except on an inside corner no doors,with face frame insets so the boxes do not touch should the angles be a bit off.
Guess some hardcore training is in order,Part editor is one area i try to avoid.

Thanks for the help and input guys.

Brian :beer:
by Brian Bauer
Wed, Apr 30 2008, 2:43PM
Forum: eCabinet Systems Software
Topic: Need an angled lower!
Replies: 26
Views: 2289

Re: Need an angled lower!

Mike,
True that,
we need angle cabinetry in general,seed cabs. There are many different combinations,but a few with easy parametric adjustables would be nice not like the corner cab. A wish list item,as I would not want to have to machine this next job with all the mters and angles involved.
Brian
by Brian Bauer
Wed, Apr 30 2008, 12:42PM
Forum: eCabinet Systems Software
Topic: Need an angled lower!
Replies: 26
Views: 2289

Re: Need an angled lower!

Thanks Dan, I got that one down now. But is it possible to have say a 48" long cabinet with 32.5 degrees cut off one end from back to front,so when two cabinets are put together in a corner their face frames meet at a miter? I have a whole job of these, a whole kitchen anyways. Can it be done w...
by Brian Bauer
Tue, Apr 29 2008, 12:15PM
Forum: eCabinet Systems Software
Topic: Need an angled lower!
Replies: 26
Views: 2289

Re: Need an angled lower!

OK what the heck gives here, If I turn off full dado it works fine,So I can't have a dadoed part to get an angled cabinet? Is this subliminal evolution happening to get us all to switch to frameless cabinetry? :roll: One more silly question how does the face frame get moved to the new front to this ...

Go to advanced search