Search found 12 matches

by Bob Blaney
Thu, Dec 09 2010, 6:32AM
Forum: eCabinet Systems Software
Topic: V6 Nest Error- Part could not be nested
Replies: 2
Views: 1156

Re: V6 Nest Error- Part could not be nested

Josh,
I redid the cabinet and checked on the grain of the back as you suggested.
That was the problem, I had it at 90 degrees instead of 0 degrees.
Now it nests.
Thanks for the tip. :beer:
by Bob Blaney
Wed, Dec 08 2010, 5:52PM
Forum: eCabinet Systems Software
Topic: Cannot open ESJ file
Replies: 4
Views: 937

Re: Cannot open ESJ file

I did not create a room. I just created a cabinet in the editor and saved it. It was saved as an esj.
I only need the one cabinet as it is standalone.
Bob
by Bob Blaney
Wed, Dec 08 2010, 6:14AM
Forum: eCabinet Systems Software
Topic: TEST
Replies: 3
Views: 819

Re: TEST

My test worked so I guess it passed. I was having an issue with Save versus Submit. :wall: :oops:
by Bob Blaney
Wed, Dec 08 2010, 6:12AM
Forum: eCabinet Systems Software
Topic: V6 Nest Error- Part could not be nested
Replies: 2
Views: 1156

V6 Nest Error- Part could not be nested

I created a simple cabinet with ply sides, ply doors, top, two shelves (all these are 3/4 ply)and a back (1/2 ply). When I run the nest program it nests the 3/4 ply parts fine. It displays a message that the 1/2 piece could not be nested for the back. Consequently the cut list and the costing does n...
by Bob Blaney
Wed, Dec 08 2010, 6:10AM
Forum: eCabinet Systems Software
Topic: Cannot open ESJ file
Replies: 4
Views: 937

Cannot open ESJ file

I created a job in version 6 based on a frameless cabinet. I saved the job as an esj. I went back later to open the file and it opens but there is no cabinet diagram. I can se a cost sheet with no data. I get the main design screen to pick something to do and the cabinet I designed is not there. Wha...
by Bob Blaney
Tue, Dec 07 2010, 6:16PM
Forum: eCabinet Systems Software
Topic: TEST
Replies: 3
Views: 819

TEST

TEST
by Bob Blaney
Sun, Jun 29 2008, 3:51PM
Forum: eCabinet Systems Software
Topic: Face Frames on side of cabinet
Replies: 2
Views: 732

Face Frames on side of cabinet

I am designing a two part china cabinet with a top that will have mullioned glass panels on the sides to be matches to the 8 lite doors on the front. :wall: I cannot figure out a technique to remove the left and right ends and add face frames so I can then add a "door" to the sides. I also...
by Bob Blaney
Sat, May 03 2008, 6:15AM
Forum: eCabinet Systems Software
Topic: New Version download
Replies: 22
Views: 2534

Re: New Version download

Hi Bob. Sorry to hear you're having trouble. So from what you are saying the update ran successfully, but you are not seeing 5.2. Did you start the application? The icon on the desktop does not change to 5.2 until you run the application the first time. If this is not your problem, maybe your virus...
by Bob Blaney
Fri, May 02 2008, 6:05AM
Forum: eCabinet Systems Software
Topic: New Version download
Replies: 22
Views: 2534

Re: New Version download

When you download it, you will have an icon on your desk top. click on it and it will go to the install wizard and install the program. It will ask you if you want to uninstall v5.1, click yes. After you are through, click on your v5.1 on the desktop and it will update and change to v5.2. The insta...
by Bob Blaney
Thu, May 01 2008, 6:16PM
Forum: eCabinet Systems Software
Topic: New Version download
Replies: 22
Views: 2534

Re: New Version download

I received the notification about V5.2. Fired up V5.1 Bld 5 and clicked on Communications Update. The D/L occurred and the install went as I expected. When I opened eCab it still said V5.1. I went to the forum and downloaded the file I found in this thread. I ran it and now it wants to know if I wan...
by Bob Blaney
Thu, Dec 06 2007, 6:42PM
Forum: Design Sharing
Topic: What Would You Like to See in Design Sharing?
Replies: 55
Views: 38485

Kerry, Thanks for sharing the china cabinet that you did. Very nice piece. Now that would be one I would purchase as a starting point. A lot of the design work for doors and moldings is done and can be modified. Hope you do put some of your items up on design sharing. And you are correct, it does no...
by Bob Blaney
Wed, Dec 05 2007, 7:01PM
Forum: Design Sharing
Topic: What Would You Like to See in Design Sharing?
Replies: 55
Views: 38485

I just reinstalled eCabinet because I want to design a china cabinet. After install I immediately went to design sharing to see what others had designed. If I found anything then I would consider paying for the design as a start. Well, I did not find one china cabinet or anything that remotely resem...

Go to advanced search