Search found 112 matches

by Terry Hall
Fri, Mar 15 2019, 12:49PM
Forum: eCabinet Systems Software
Topic: Shelf Standards or pilasters
Replies: 8
Views: 1340

Re: Shelf Standards or pilasters

I almost wonder if one could set up partitions, then just cut the dado and not the partition itself.
by Terry Hall
Tue, Mar 12 2019, 8:07AM
Forum: eCabinet Systems Software
Topic: Hp Printers - No leaders
Replies: 8
Views: 1538

Re: Hp Printers - No leaders

Here is something interesting, to me anyway. My printer prints the leaders fine in my other cad programs, just not in Ecabinets. It's something specific to Ecabinets apparently, but I haven't figured it out yet. Maybe TMC would have some idea(s).
by Terry Hall
Fri, Mar 08 2019, 8:24AM
Forum: eCabinet Systems Software
Topic: Hp Printers - No leaders
Replies: 8
Views: 1538

Re: Hp Printers - No leaders

Nope, thanks anyway Kerry, but the Universal Print Driver didn't work for me. Message said it wasn't compatible with my printer. Maybe my printer is too old, I've probably had it for 5 or six years. :wall:
by Terry Hall
Fri, Mar 01 2019, 2:11PM
Forum: eCabinet Systems Software
Topic: Hp Printers - No leaders
Replies: 8
Views: 1538

Re: Hp Printers - No leaders

Thanks Brad I'll look at that.

Just saw your post Kerry. For sure and thanks, I'm going to download that this afternoon after I get done spraying some cabinet doors. :D
by Terry Hall
Fri, Mar 01 2019, 12:23PM
Forum: eCabinet Systems Software
Topic: Ecab gets stuck returning to Custom Layout from LDE
Replies: 8
Views: 1366

Re: Ecab gets stuck returning to Custom Layout from LDE

I tried it just as you described Leo. Mine does not do that and I've done what you are doing in the past and don't recall it ever doing it. I'd say you're right that it's probably a driver problem. You downloaded from Nvidia's site I assume. I always download from there and wish there was a way to p...
by Terry Hall
Wed, Feb 27 2019, 10:11AM
Forum: eCabinet Systems Software
Topic: Hp Printers - No leaders
Replies: 8
Views: 1538

Re: Hp Printers - No leaders

Right Ralph, I use Windows 10 and when it installs updates for my Nvidia driver I have to remove it and go to the Nvidia website for the driver. It hasn't been as bad lately, not sure why. I've checked HP's website for a new driver to no avail. I've installed and re-installed from my disk, but also ...
by Terry Hall
Mon, Feb 18 2019, 8:31AM
Forum: eCabinet Systems Software
Topic: Hp Printers - No leaders
Replies: 8
Views: 1538

Hp Printers - No leaders

I read this post by Kerry in another individual's topic - My problem now is when I try to print from the LDE to any of the HP printers we have at work, the leader lines on dimensions won't print. I get the dimension and arrows but no leaders. It works fine with my Dell and Canon printers at home. At...
by Terry Hall
Tue, Feb 05 2019, 9:23AM
Forum: eCabinet Systems Software
Topic: Need A FF Cabinet for A Farm Sink
Replies: 3
Views: 1076

Re: Need A FF Cabinet for A Farm Sink

Thank you so much JR and Don. Can't believe I've done this for almost 40 years and haven't done one of these yet. I actually drew one yesterday very similar to yours JR, only with a toekick. Thank you both and pm me and I'll gladly compensate you.
by Terry Hall
Mon, Feb 04 2019, 3:58PM
Forum: eCabinet Systems Software
Topic: Need A FF Cabinet for A Farm Sink
Replies: 3
Views: 1076

Need A FF Cabinet for A Farm Sink

I have two jobs that have unfortunately converged due to weather and other delays on the one. I don't have any extra time to waste at the computer. I will happily pay for a face frame farm sink cabinet that I can resize once I receive the actual sink. Let me know if you can provide one and the cost....
by Terry Hall
Sat, Nov 17 2018, 2:30PM
Forum: eCabinet Systems Software
Topic: Adding a diagonal cut line on a part
Replies: 3
Views: 979

Re: Adding a diagonal cut line on a part

Or, you can use the chamfer in part editor as well.
by Terry Hall
Fri, Jul 06 2018, 8:49AM
Forum: eCabinet Systems Software
Topic: Nesting Error
Replies: 10
Views: 2412

Re: Nesting Error

Just thinking, another way to check would be to remove one cabinet at a time from nesting, then re-nest and see if the job will nest properly.
by Terry Hall
Fri, Jul 06 2018, 8:42AM
Forum: eCabinet Systems Software
Topic: Nesting Error
Replies: 10
Views: 2412

Re: Nesting Error

Nat, some time ago I think I may have had a very similar error. After some frustration I found that it was because I had the wrong tool for cutting a dado. It seems like maybe I was trying to cut a 1/4" dado with a 3/8" cutter, or something like that. I had to check each cabinet to figure ...
by Terry Hall
Wed, Nov 29 2017, 9:17AM
Forum: eCabinet Systems Software
Topic: Nesting discrepancy
Replies: 11
Views: 2885

Re: Nesting discrepancy

Why would a control computer be giving better results? Does the program know or care about weather there's a USB cable connecting it to a machine? Basically, the question to my mind is that software is software correct? How would having a USB cable running to a machine give the program an advantage...
by Terry Hall
Tue, Nov 28 2017, 9:20AM
Forum: eCabinet Systems Software
Topic: Nesting discrepancy
Replies: 11
Views: 2885

Re: Nesting discrepancy

Mine has always been that way too. Optimization at the control computer has always been better for me and it was always my understanding that was the norm.
by Terry Hall
Tue, Sep 12 2017, 2:12PM
Forum: eCabinet Systems Software
Topic: E Cabinets has stopped working
Replies: 1
Views: 1414

Re: E Cabinets has stopped working

Carmen, I have this intermittently. I'm wondering now if mine is caused after windows 10 does an update. I have it set to update automatically. When it updates it wants to update my graphics driver and I get a message saying "unsuccessful" for the driver installation. Then I go to the Nvid...

Go to advanced search