Search found 414 matches

by Will Williamson
Fri, Aug 16 2019, 1:30PM
Forum: eCabinet Systems Software
Topic: Kinda off the subject of eCabs - TWD CNC machines
Replies: 16
Views: 529

Re: Kinda off the subject of eCabs - TWD CNC machines

Before noon, my time, eastern standard.
by Will Williamson
Fri, Aug 16 2019, 7:43AM
Forum: eCabinet Systems Software
Topic: Kinda off the subject of eCabs - TWD CNC machines
Replies: 16
Views: 529

Re: Kinda off the subject of eCabs - TWD CNC machines

If you want to call me, tomorrow morning, Saturday, I will answer all your questions 810 310 1111 but Jerremy answered just fine I will agree with him on all aspects. Thermwood tech support is the very best none better in 13 years I have only replaced the spindle once at about 9 years old
by Will Williamson
Fri, Aug 16 2019, 7:06AM
Forum: eCabinet Systems Software
Topic: Roughing button missing in CN 6.14
Replies: 9
Views: 261

Re: Roughing button missing in CN 6.14

Hey Clint can I upgrade my CS45 -510 to windows 10 ?
by Will Williamson
Sat, Aug 10 2019, 6:33AM
Forum: Thermwood 3-Axis Machinery
Topic: Fixture offset changes Model CS-45 WinXP vs. C-50 Win7
Replies: 4
Views: 219

Re: Fixture offset changes Model CS-45 WinXP vs. C-50 Win7

Set the fixture offset and then push F10 then then press Y to keep the changes.
by Will Williamson
Wed, Aug 07 2019, 1:59PM
Forum: eCabinet Systems Software
Topic: glass Doors how to
Replies: 4
Views: 341

Re: glass Doors how to

Thanks Leo, But it looks like that only applies if you are using Conestoga Doors
by Will Williamson
Thu, Jul 11 2019, 2:57PM
Forum: eCabinet Systems Software
Topic: glass Doors how to
Replies: 4
Views: 341

Re: glass Doors how to

Thanks Jeremy
by Will Williamson
Thu, Jul 11 2019, 8:48AM
Forum: eCabinet Systems Software
Topic: glass Doors how to
Replies: 4
Views: 341

glass Doors how to

How can you make, a one piece, mdf or slab door, open for glass? short of going into the part editor and drawing each door.
After 13 years of owning my machine, I am finally doing my first set of Kitchen Cabinets.
by Will Williamson
Tue, Jun 25 2019, 5:59AM
Forum: Thermwood 3-Axis Machinery
Topic: Sliding dovetails
Replies: 3
Views: 1093

Re: Sliding dovetails

I milled a pocket 3/4 deep, then inlined with a dovetail tool, I drew the dovetail tool. to determine my offsets. i started the cut off the material and then cut the, two long sides and the end. then I took some flat stock and outlined it. there again using my cross section to determine the offset. ...
by Will Williamson
Mon, Jun 24 2019, 1:20PM
Forum: Thermwood 3-Axis Machinery
Topic: Sliding dovetails
Replies: 3
Views: 1093

Re: Sliding dovetails

Yes, we have, cut sliding dove tails, into solid wood counter tops, to hold flat.
by Will Williamson
Tue, Mar 05 2019, 6:34AM
Forum: Thermwood 3-Axis Machinery
Topic: Machining 2 3/4'' thick solid oak
Replies: 3
Views: 981

Re: Machining 2 3/4'' thick solid oak

What are your speeds and feeds on this job. I do this all the time on, solid wood. I use Vortex tools with down spiral. Chip Breaker, Rougher, or finisher, adjust tool, for needed edge surface quality. These tools last for all day. If you need smooth edges, try a 5/8 down spiral rougher, followed by...
by Will Williamson
Mon, Nov 26 2018, 8:14AM
Forum: eCabinet Systems Software
Topic: Shop Drawings
Replies: 4
Views: 1317

Re: Shop Drawings

Its called Autocad Kerry. hey good to see you still hanging in there
by Will Williamson
Fri, Aug 10 2018, 9:07AM
Forum: Thermwood 3-Axis Machinery
Topic: Keyboard cleaning
Replies: 3
Views: 1783

Re: Keyboard cleaning

Unplug your existing key board and plug anew one in. Use a desk top key board. I don't like that vertical keyboard any way.
by Will Williamson
Sat, Jun 30 2018, 10:11AM
Forum: Thermwood 3-Axis Machinery
Topic: Y axis Out of bounds
Replies: 12
Views: 4432

Re: Y axis Out of bounds

Thanks Rob, I had run into this issue, running dxf files, thru Control Nesting . Have not had the issue since. Using our current software to save g code to NC files.91 parts with 15 features, make your head fuzzy.
by Will Williamson
Wed, Jun 27 2018, 11:47AM
Forum: Thermwood 3-Axis Machinery
Topic: Y axis Out of bounds
Replies: 12
Views: 4432

Re: Y axis Out of bounds

Rob, Do you use Mastercam, to write code directly, to your machine? or do you still use control nesting?
Nothing related to your issue, just curious.
Thanks Will
by Will Williamson
Thu, Apr 05 2018, 3:07PM
Forum: Thermwood 3-Axis Machinery
Topic: Aspire export/import
Replies: 10
Views: 3497

Re: Aspire export/import

Mark check this post from a few years back the Vcarve PP from Josh will work for Aspire
viewtopic.php?f=7&t=13164&hilit=josh+post

Go to advanced search