Search found 413 matches

by Al Navas
Sat, Dec 08 2007, 8:30AM
Forum: Customer Images
Topic: OT: NOT an eCabs job...
Replies: 17
Views: 4640

Re:

. ...I'm just unsure what would happen when the water gets into the skimmer during the winter. Of course, we haven't had a "hard freeze" in 50 years so it may not be a concern. Ahhh...Sorry I did not address this earlier. The skimmer lines are sealed shut after winterizing, using large ru...
by Al Navas
Sat, Dec 08 2007, 8:22AM
Forum: Customer Images
Topic: OT: NOT an eCabs job...
Replies: 17
Views: 4640

Re:

. ...One question though...we were told to drain the water level to just under the skimmer for the winter. If rain runs through the mesh, do you have any freezing problems? I believe you probably have a little bit colder winters than we do here :D Do you just blow the lines out and not drain the po...
by Al Navas
Fri, Dec 07 2007, 8:46PM
Forum: eCabinet Systems Software
Topic: Miter front to corner cabinet
Replies: 18
Views: 2334

.

Thanks, Kerry. I must remember this when I see something strange going on.


Al
http://blog.sandal-woods.com

.
by Al Navas
Fri, Dec 07 2007, 8:07PM
Forum: eCabinet Systems Software
Topic: Miter front to corner cabinet
Replies: 18
Views: 2334

Re:

. When you extrude any part of the cabinet beyond the cabinet dimensions, they become really funky and don't want to act right. Kerry's inset is the best way for sure. Just to follow through: In the attached image: 1. Should I offset the sides, or the top and deck? 2. What I need: I will be using k...
by Al Navas
Fri, Dec 07 2007, 1:15PM
Forum: eCabinet Systems Software
Topic: Miter front to corner cabinet
Replies: 18
Views: 2334

Now I am on the same wavelength, Kerry. Thanks!


Al
http://blog.sandal-woods.com
by Al Navas
Fri, Dec 07 2007, 9:54AM
Forum: eCabinet Systems Software
Topic: Miter front to corner cabinet
Replies: 18
Views: 2334

Re:

Doug, The proper way to build this cabinet would be to take off all the insets on your left and right sides then add a 1.25" bottom inset to the deck. Remove the scribes to your face frame. Go to corner settings and check the Left and right sides mitered box. This causes eCabinets to add enoug...
by Al Navas
Mon, Dec 03 2007, 5:55PM
Forum: Customer Images
Topic: Girls Dresser. Sorry, I messed up. Here is the ecabinets pic
Replies: 8
Views: 2296

John,

Where in Missouri are you located? Please let me know. I am near St Joseph, in NW MO. Welcome to the forum!


Al
http://blog.sandal-woods.com
by Al Navas
Wed, Nov 21 2007, 3:01PM
Forum: eCabinet Systems Software
Topic: Question about the Quadro tweak utility
Replies: 9
Views: 1126

Dan,

You can see the source of my confusion below - I cannot specify 16X with Tweak 1.0.5.1, as the only options are Disabled, and 4X. I want my money back! :lol:

Dean - Is Tweak 1.0.5.1 supposed to allow the selection of 16X anti-alias?
by Al Navas
Wed, Nov 21 2007, 10:33AM
Forum: eCabinet Systems Software
Topic: Question about the Quadro tweak utility
Replies: 9
Views: 1126

hmmmmm.... I do think the real reason is that 16X is not as good quality as 4X, so it is not allowed in Tweak, as Dean reported.
by Al Navas
Wed, Nov 21 2007, 8:59AM
Forum: eCabinet Systems Software
Topic: Question about the Quadro tweak utility
Replies: 9
Views: 1126

I believe the 16X is just not available while the Tweak Utility is installed. The image below shows what I get when it is not installed, and I select the card's Advanced Settings:

Image



Al
by Al Navas
Tue, Nov 20 2007, 11:46PM
Forum: eCabinet Systems Software
Topic: Question about the Quadro tweak utility
Replies: 9
Views: 1126

Re: Question about the Quadro tweak utility

I lurk quite a bit here & will someday be a contributor. In the meantime, can anyone help with this? Last week I bought an M90 from the Dell business outlet. It has a Quadro FX 3500 video card w/512MB. I've installed the latest NVidia driver (& checked to make sure it is properly installed)...
by Al Navas
Wed, Nov 07 2007, 8:41PM
Forum: eCabinet Systems Software
Topic: Noobee with a question?
Replies: 3
Views: 641

Re: Noobee with a question?

I hope this is not a totally stupid question but I am just beginning to try to learn this program. Totally intimidating... Dave, Welcome to the forum! Please, understand that the ONLY stupid question is one you don't ask. No matter how simple it appears, if YOU don't know HOW to do something in the...
by Al Navas
Wed, Nov 07 2007, 2:16PM
Forum: eCabinet Systems Software
Topic: M90
Replies: 7
Views: 1018

Re:

This kinda caught me off guard a little. Since we are a VAR for Dell, I access the Dell site through their Extranet. We can still buy the M90. After Jason pointed out your posting, I went and did a double-check and sure enough, the retail store no longer lists the M90 but the Extranet still does. A...
by Al Navas
Tue, Nov 06 2007, 10:49AM
Forum: eCabinet Systems Software
Topic: Problems with Detail Room
Replies: 9
Views: 1278

Edit, to delete the content, as it is a duplicate.

This is a duplicate post - PLEASE delete. Thanks!


Al
by Al Navas
Tue, Nov 06 2007, 10:48AM
Forum: eCabinet Systems Software
Topic: Problems with Detail Room
Replies: 9
Views: 1278

Update: I looked at eCabinets.ini, and found that PlaceItemGridSpacing=0.0312 !!! I changed this to 12 inches, and NOW all is well. My thanks to all who have looked into this. I have no idea what might have changed this setting, but now all seems well. My sincere thanks to Scott, to Justin, and to J...

Go to advanced search