Search found 887 matches

by Damon Nabors
Thu, Jun 11 2009, 7:09AM
Forum: Thermwood 3-Axis Machinery
Topic: More school fees
Replies: 3
Views: 955

Re: More school fees

I cut alot of MDF here in the shop and have little problem doing so. I would have to wonder if your dust collection is sufficient enough or maybe has a restriction cuttin down the cfm's. Just a thought.
by Damon Nabors
Sun, Jun 07 2009, 1:58PM
Forum: eCabinet Systems Software
Topic: Saving as a .dxf file
Replies: 2
Views: 429

Re: Saving as a .dxf file

Thanks kerry, I was hoping I could save the geometry as a dxf file but now that I think about it, that has been covered to prevent people from saving as a dxf and cutting on competitor machines.

Thanks again,

Damon
by Damon Nabors
Sun, Jun 07 2009, 11:40AM
Forum: eCabinet Systems Software
Topic: Saving as a .dxf file
Replies: 2
Views: 429

Saving as a .dxf file

Its been a while since I tried this but I thought you could take a part into the parts editor and create your geometry and then save the geometry as a dxf file. I can only get a x_t extention to show up.
Maybe I dreamed this.

Thanks,
Damon
by Damon Nabors
Tue, May 12 2009, 10:36PM
Forum: Thermwood 3-Axis Machinery
Topic: MDF Doors?
Replies: 4
Views: 749

Re: MDF Doors?

as others have stated, the MDF grade makes a big difference and you might adjust your step over. A smaller step over will take a little longer but will produce a better end result. I am assuming you are using the profile modeler.
by Damon Nabors
Fri, May 01 2009, 8:38PM
Forum: Thermwood 3-Axis Machinery
Topic: Anyone Using the CS 41?
Replies: 27
Views: 3375

Re: Anyone Using the CS 41?

Kerry, I looked at the 41 when I purchased my 45. There are limitations to the 41. It runs a little slower, you are limited to the 4x8 table, and you can not use the rotary play back with the 41 and I am wanting to say that there are fewer tool holder positions. Are you thinking about getting into a...
by Damon Nabors
Wed, Apr 29 2009, 1:05PM
Forum: eCabinet Systems Software
Topic: Partition and shelf pin holes
Replies: 2
Views: 420

Re: Partition and shelf pin holes

One thing to remember on thinner material. If you are placing shelf pin holes on both sides and wish to have your shelving level across the cabinet. The length of the pins may interfere with each other. I try to stay with 3/4" for center partitions to avoid this problem.
by Damon Nabors
Wed, Apr 29 2009, 12:43PM
Forum: eCabinet Systems Software
Topic: Problem with Blind Dado
Replies: 3
Views: 485

Re: Problem with Blind Dado

Never Mind, Thermwood came to the rescue again. Thanks
by Damon Nabors
Wed, Apr 29 2009, 12:25PM
Forum: eCabinet Systems Software
Topic: Problem with Blind Dado
Replies: 3
Views: 485

Problem with Blind Dado

Somebody want to take a look at this problem. The back left tenon has a chamfer cut rather than a tenon and the right tenon on the Back is wireframed. If I change the back left to BUTT is correct the right side. What the flip is going on now?

Thanks,
by Damon Nabors
Sat, Apr 18 2009, 10:33PM
Forum: eCabinet Systems Software
Topic: Unable to Edgeband Part
Replies: 6
Views: 650

Re: Unable to Edgeband Part

No problem, Glad I was able to help.
by Damon Nabors
Sat, Apr 18 2009, 8:57PM
Forum: eCabinet Systems Software
Topic: Unable to Edgeband Part
Replies: 6
Views: 650

Re: Unable to Edgeband Part

Here is your cabinet with edgebanding. You need to open the construction settings and set the deck , front edge to Butt . You will notice the area is blank.
by Damon Nabors
Sat, Apr 18 2009, 7:22PM
Forum: eCabinet Systems Software
Topic: Unable to Edgeband Part
Replies: 6
Views: 650

Re: Unable to Edgeband Part

can you post the cabinet so we can take a look at it?
by Damon Nabors
Tue, Apr 14 2009, 5:43PM
Forum: eCabinet Systems Software
Topic: Combining Two Cabinets into One
Replies: 8
Views: 859

Re: Combining Two Cabinets into One

just set a bottom offset on the style for the upper cabinet so that they extend down the length of the lower cabinet.
by Damon Nabors
Sat, Apr 11 2009, 8:45PM
Forum: eCabinet Systems Software
Topic: shop bot
Replies: 19
Views: 2747

Re: shop bot

We now offer an extensive body of cabinet and furniture libraries and carving files that are all available free. Ken, That's great that you now offer these features for free. I just wish your salesman that called me about six weeks ago and asked if I would be interested in purchasing those carvings...
by Damon Nabors
Wed, Apr 01 2009, 10:24PM
Forum: Thermwood 3-Axis Machinery
Topic: Maintenance Groups Missing
Replies: 3
Views: 698

Re: Maintenance Groups Missing

Mine did that with the last update. It screwed up one of the files. I forget now which one but if you call THM they can tell you which one you need to erase and your maintenance will start working again.
by Damon Nabors
Mon, Mar 30 2009, 5:03PM
Forum: Lounge
Topic: Today's Inspirational Message!!!
Replies: 0
Views: 602

Today's Inspirational Message!!!

Today's Inspirational Message




Never piss off a guy that owns a backhoe
truck picture (2).jpg
truck picture (2).jpg (80.12 KiB) Viewed 604 times

Go to advanced search