Search found 536 matches

by Leo Graywacz
Thu, Mar 15 2007, 5:09PM
Forum: eCabinet Systems Software
Topic: Center of Axis
Replies: 2
Views: 487

Center of Axis

I have just made an assembly of 3 cabinets. When I rotate them in the cabinet editor the rotational center of axis is to the far right of the cabinet instead of in the center. When I use the end key to see the back of the cabinet it rotates off the screen. Is there a way to re-center the axis? What ...
by Leo Graywacz
Thu, Mar 15 2007, 11:28AM
Forum: eCabinet Systems Software
Topic: Materials File/folder
Replies: 8
Views: 1164

I transfered the MBD and the INI file and it solved the problem. Thanks Dan.
by Leo Graywacz
Thu, Mar 15 2007, 7:38AM
Forum: eCabinet Systems Software
Topic: Materials File/folder
Replies: 8
Views: 1164

Re:

Mike Seisser wrote:Gettin' your fair share of worms there Mr. Early Bird? :wink: I know you're in a different timezone and all, but..........


My post listing shows I posted at 7:20am when I really posted at 8:20am. DST is screwed up.
by Leo Graywacz
Thu, Mar 15 2007, 7:20AM
Forum: eCabinet Systems Software
Topic: Materials File/folder
Replies: 8
Views: 1164

Thanks Dan. I'll transfer and install those files ans see what happens. I was looking at the problem closer and it looks like it has a weird twist to it. I would highlight a part and it would tell me that it was the correct sheet stock/board stock and species, yet it was showing the wrong picture fo...
by Leo Graywacz
Wed, Mar 14 2007, 11:07PM
Forum: eCabinet Systems Software
Topic: Materials File/folder
Replies: 8
Views: 1164

Materials File/folder

I am in the process of transfering my eCabs files from my desktop to my laptop. Which folder are my material filed in. These are the materials I have defined, my sheet stock, my board stock, banding and countertop stock. I would like to transfer them over but can't locate them. I have transfered som...
by Leo Graywacz
Sun, Mar 04 2007, 3:58PM
Forum: eCabinet Systems Software
Topic: Upgrading memory
Replies: 4
Views: 796

OK, I get the voltage thing now. It isn't what is required it is what the chips regulator is set at. So as long as the board provides more voltage than the memory needs it can regulate it down to the correct voltage, check. The memory companies are telling you this because they want to let you know ...
by Leo Graywacz
Sun, Mar 04 2007, 3:14PM
Forum: eCabinet Systems Software
Topic: Upgrading memory
Replies: 4
Views: 796

Thanks Dan. I went to Crucial.com and they have a little program that you download and it runs a system scan. It will tell you what you have installed, how many open slots you have, and how much memory your system will max out at. It also gives you choices of what memory is compatible with your syst...
by Leo Graywacz
Sun, Mar 04 2007, 12:15PM
Forum: eCabinet Systems Software
Topic: Upgrading memory
Replies: 4
Views: 796

Upgrading memory

Right now I have 512MB PC2-3200 (CL3) memory in my P4 2.8Ghz Dell. All of the upgrades of memory are rated at PC2-4200 and up. I plan on getting 2GB more. If I mix the two speeds, my new memory will be at the mercy of the slower speed memory existing in the computer now. Is it better (faster) to rem...
by Leo Graywacz
Sat, Mar 03 2007, 8:00PM
Forum: eCabinet Systems Software
Topic: Problems with saving geometry created in part editor contour
Replies: 2
Views: 467

Are you associating the cabinet sides to the cabinet after you put the holes and constraints in them?
by Leo Graywacz
Mon, Feb 26 2007, 10:04PM
Forum: eCabinet Systems Software
Topic: Best way to email files
Replies: 9
Views: 1057

What I think his problem might be is that the file is to large to send by way of email. Most ISP's set limits on how large of a file they allow you to send. I have a subscription to a service called X-Drive which is on online storage/sharing area set up to be an Internet hard drive. You can upload f...
by Leo Graywacz
Sun, Feb 25 2007, 1:58PM
Forum: eCabinet Systems Software
Topic: POOF!! Gone.
Replies: 1
Views: 437

POOF!! Gone.

On several occasions I have had the eCab software just disappear off the screen in the middle of a job. What I trying to say is that I am working on a job and do some input and the software just blinks out and the program just ends itself, instantly. No warning, no error message, completely out of t...
by Leo Graywacz
Sat, Feb 24 2007, 3:50PM
Forum: eCabinet Systems Software
Topic: Mitered Corner On Angle Upper
Replies: 2
Views: 478

And thats what I did. Thanks Dan
by Leo Graywacz
Sat, Feb 24 2007, 3:21PM
Forum: eCabinet Systems Software
Topic: Mitered Corner On Angle Upper
Replies: 2
Views: 478

Mitered Corner On Angle Upper

I have an Face Framed Angled Upper cabinet that I can't get the face frame edges to be mitered. I think I have the appropriate box checked in the construction settings ANGLED FRONT FACE FRAME SETTING box is checked. What else do I need to do. I tried removing the FF and installing it after the box w...
by Leo Graywacz
Sat, Feb 24 2007, 11:28AM
Forum: eCabinet Systems Software
Topic: I was wondering...
Replies: 1
Views: 461

I was wondering...

If the Constraint Manager was to be use in this fashion. Lately I have been designing the top rails of my cabinets with designs to make them more appealing. Usually for open shelving and not cabinets with doors. But when I am designing them in the parts editor, in the beginning when I was new to eCa...
by Leo Graywacz
Thu, Feb 22 2007, 8:22PM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 2754

OK I messed around with it some and went back to my original formula with a modification to make it work. Instead of (h-7)/3 I made it into .333*(h-7) which shows up as .333(h-7) but still works the same as your h/3-2.33 which is much less intuitive. I think one of the problems I was having is that ...

Go to advanced search