Search found 542 matches

by Leo Graywacz
Mon, Feb 26 2007, 10:04PM
Forum: eCabinet Systems Software
Topic: Best way to email files
Replies: 9
Views: 1723

What I think his problem might be is that the file is to large to send by way of email. Most ISP's set limits on how large of a file they allow you to send. I have a subscription to a service called X-Drive which is on online storage/sharing area set up to be an Internet hard drive. You can upload f...
by Leo Graywacz
Sun, Feb 25 2007, 1:58PM
Forum: eCabinet Systems Software
Topic: POOF!! Gone.
Replies: 1
Views: 511

POOF!! Gone.

On several occasions I have had the eCab software just disappear off the screen in the middle of a job. What I trying to say is that I am working on a job and do some input and the software just blinks out and the program just ends itself, instantly. No warning, no error message, completely out of t...
by Leo Graywacz
Sat, Feb 24 2007, 3:50PM
Forum: eCabinet Systems Software
Topic: Mitered Corner On Angle Upper
Replies: 2
Views: 695

And thats what I did. Thanks Dan
by Leo Graywacz
Sat, Feb 24 2007, 3:21PM
Forum: eCabinet Systems Software
Topic: Mitered Corner On Angle Upper
Replies: 2
Views: 695

Mitered Corner On Angle Upper

I have an Face Framed Angled Upper cabinet that I can't get the face frame edges to be mitered. I think I have the appropriate box checked in the construction settings ANGLED FRONT FACE FRAME SETTING box is checked. What else do I need to do. I tried removing the FF and installing it after the box w...
by Leo Graywacz
Sat, Feb 24 2007, 11:28AM
Forum: eCabinet Systems Software
Topic: I was wondering...
Replies: 1
Views: 539

I was wondering...

If the Constraint Manager was to be use in this fashion. Lately I have been designing the top rails of my cabinets with designs to make them more appealing. Usually for open shelving and not cabinets with doors. But when I am designing them in the parts editor, in the beginning when I was new to eCa...
by Leo Graywacz
Thu, Feb 22 2007, 8:22PM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

OK I messed around with it some and went back to my original formula with a modification to make it work. Instead of (h-7)/3 I made it into .333*(h-7) which shows up as .333(h-7) but still works the same as your h/3-2.33 which is much less intuitive. I think one of the problems I was having is that ...
by Leo Graywacz
Thu, Feb 22 2007, 7:56PM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

Re:

Maybe this is one of the reasons I don't like the constraint manager :lol: Leo and I both were trying our best to constrain the WIDTH of the part to the WIDTH of the cabinet as one would look at the part ON the cabinet. That area could be a little more intuitive when it comes to the help for formul...
by Leo Graywacz
Thu, Feb 22 2007, 4:16PM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

Here is the cabinet I'm trying to get to work in the constraints manager if anyone else wants to give it a shot.
by Leo Graywacz
Thu, Feb 22 2007, 3:56PM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

Re:

DanEpps wrote:
Leo Graywacz wrote:They sure aren't acting like it. :lol:


Sure they were...the results were variable weren't they? :wink:


Sure if unpredictable and variable have the same meaning. :lol:
by Leo Graywacz
Thu, Feb 22 2007, 3:48PM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

They sure aren't acting like it. :lol:
by Leo Graywacz
Thu, Feb 22 2007, 3:18PM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

When you are using the terms W(idth) & H(eight) in the constraint manager are they variable terms with the data coming from the cabinet width and height input areas in the cabinet editor or are they a constant being derived when you make the formula in the constraint manager?
by Leo Graywacz
Thu, Feb 22 2007, 11:56AM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

Re:

Here is what I'm talking about with the funky change. The constraint is w-1. Notice that the top arc disappeared and the constraint is at the bottom??? Wow, to think I might be able to teach a guru something. Dan, you need to trap the arcs within the constraint editor. You have to give them real nu...
by Leo Graywacz
Thu, Feb 22 2007, 9:02AM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

Re:

Justin D Melhiser wrote:Send it to my email cabinets@thermwood.com and feel free to give me a call with any other questions at 1-800-533-6901 ext. 227


E-mail sent to you Justin, Thanks.
by Leo Graywacz
Thu, Feb 22 2007, 8:48AM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

Re:

Never mind that Leo, further testing shows it doesn't work just right :oops: I'll see if I can come up with a set of constraints that will work for you. Been there, did that. I've spent quite a bit of time on this playing with formulas. The one that should work won't input properly. (w-7)/3 Thanks ...
by Leo Graywacz
Thu, Feb 22 2007, 2:14AM
Forum: eCabinet Systems Software
Topic: Constraint Manager
Replies: 24
Views: 3505

Constraint Manager

I have a cabinet that I want to apply constraints to the top rail. What I have is a cabinet with three arches. I want the 3 arches to always be equal to each other. On the left and right there should be a flat area 1/2\" long before the arch starts, then in the middle (2 middles actually) I wan...

Go to advanced search