Search found 222 matches

by Nemanja Vujkovic
Mon, Mar 09 2009, 1:38PM
Forum: eCabinet Systems Software
Topic: Moving cabinets
Replies: 8
Views: 932

Re: Moving cabinets

One more thing Sergio, i am not sure that you can instal a cabinet so that the side of it butts into the face of the other cab. What Michael said should work. What you can also do is take both cabinet into the Cabinet Editor and make one assambly. Than you can instal both of the cabinets together as...
by Nemanja Vujkovic
Mon, Mar 09 2009, 1:18PM
Forum: eCabinet Systems Software
Topic: Moving cabinets
Replies: 8
Views: 932

Re: Moving cabinets

Sergio,
try to go to Define Standard Dimesions and change your setting there. After you do that, try to place your cabinet in the desired position.

Nemanja
by Nemanja Vujkovic
Mon, Mar 09 2009, 11:53AM
Forum: eCabinet Systems Software
Topic: New kitchen layout
Replies: 1
Views: 413

Re: New kitchen layout

Sergio,
set your parameters, save your basic cabinet (the seed cabinet) in a new directory and next time that you need to creat a similar design, just pull it from that directory.

Nemanja
by Nemanja Vujkovic
Mon, Mar 09 2009, 9:25AM
Forum: Thermwood 3-Axis Machinery
Topic: 3cm Solid Surface Material
Replies: 8
Views: 1889

Re: 3cm Solid Surface Material

Keith,
try 18000-20000 rpm and at 400-500 ipm. You can allways slow it down if the feed speed is too fast!
However, i think the safest bet is 3/4" straight flute at 15000 rpm and 500 ipm.

Nemanja
by Nemanja Vujkovic
Mon, Mar 09 2009, 6:13AM
Forum: eCabinet Systems Software
Topic: Angled sides on a cabinet
Replies: 7
Views: 861

Re: Angled sides on a cabinet

I am using microvellum only because it is a lot easier to make the cabinet there than in eCabs. Once i make the cab in microvellum, i might as well cut it from there, it save a step where i would have to take the .dxf created in microvellum and importing it in eCabs.

Nemanja
by Nemanja Vujkovic
Fri, Mar 06 2009, 3:08PM
Forum: eCabinet Systems Software
Topic: Angled sides on a cabinet
Replies: 7
Views: 861

Re: Angled sides on a cabinet

We are using microvallum and eCabs, however we have a lot of problems with microvallum. The nest that i attached is a job done in microvallum, but we have trouble cutting from microvallum. i know i can get the .dxf into the PE, but i was hoping that there is a function that can do this as a cabinet,...
by Nemanja Vujkovic
Fri, Mar 06 2009, 2:36PM
Forum: eCabinet Systems Software
Topic: Angled sides on a cabinet
Replies: 7
Views: 861

Re: Angled sides on a cabinet

I know that. I guess i was not clear enough. I was hopping that there is a way to do this automaticaly, something that would take only few seconds.

Nemanja
by Nemanja Vujkovic
Fri, Mar 06 2009, 1:40PM
Forum: eCabinet Systems Software
Topic: Need training/tutoring on eCab in Kansas City area
Replies: 4
Views: 619

Re: Need training/tutoring on eCab in Kansas City area

Hi Mark,
if you post your question on the forum they get answered quickly and accurately. There is also a manual on the web site that you can read. You should also watch the videos that are in eCab's fornt page.

Nemanja
by Nemanja Vujkovic
Fri, Mar 06 2009, 12:15PM
Forum: eCabinet Systems Software
Topic: Angled sides on a cabinet
Replies: 7
Views: 861

Angled sides on a cabinet

I have include a .dxf file of microvallum nest of a microwave cabinet with angled sides. I am just wondering is somethig like this possible to creat in eCabinets? If it is, how can i do it? If not, is it going to be possible in the future?
Thank You

Nemanja
by Nemanja Vujkovic
Thu, Mar 05 2009, 12:57PM
Forum: Lounge
Topic: Something to think about
Replies: 5
Views: 1176

Re: Something to think about

This is interesting.
When i still lived in Europe i was allways buying Levi's pants made in USA. How come when i moved here i cannot find any of them made here? It's either Mexico or Turkey. :(

Nemanja
by Nemanja Vujkovic
Tue, Mar 03 2009, 2:31PM
Forum: Thermwood 3-Axis Machinery
Topic: 3cm Solid Surface Material
Replies: 8
Views: 1889

Re: 3cm Solid Surface Material

Keith,
have you tried a bigger bit, let's say 3/4" diameter? You can cut it in one pass with this bit.
by Nemanja Vujkovic
Tue, Mar 03 2009, 2:27PM
Forum: Thermwood 3-Axis Machinery
Topic: Something is off with outline cut
Replies: 4
Views: 670

Re: Something is off with outline cut

Thank you Daniel.

Nemanja
by Nemanja Vujkovic
Tue, Mar 03 2009, 12:13PM
Forum: Thermwood 3-Axis Machinery
Topic: Something is off with outline cut
Replies: 4
Views: 670

Re: Something is off with outline cut

Hi everyone,
I was just wondering what was figured on the problem I had. Am i correct in my asamption?
by Nemanja Vujkovic
Tue, Mar 03 2009, 11:56AM
Forum: Lounge
Topic: how can you protect your drawing
Replies: 38
Views: 5274

Re: how can you protect your drawing

That is true, however, it might help you feel a bit better! :lol:
by Nemanja Vujkovic
Tue, Mar 03 2009, 11:55AM
Forum: eCabinet Systems Software
Topic: "The parameter is incorrect"
Replies: 3
Views: 473

Re: "The parameter is incorrect"

Hi Steve,
can you post your files on the forum!

Nemanja

Go to advanced search