Search found 214 matches

by Larry Epplin
Tue, Sep 15 2009, 9:35AM
Forum: eCabinet Systems Software
Topic: SB Link Tenon Dado Cut Direction
Replies: 15
Views: 2487

Re: SB Link Tenon Dado Cut Direction

Hi Don. We should have it ready this week.
by Larry Epplin
Mon, Sep 14 2009, 9:47AM
Forum: eCabinet Systems Software
Topic: SB Link Tenon Dado Cut Direction
Replies: 15
Views: 2487

Re: SB Link Tenon Dado Cut Direction

Gary, We are adding the cut through value to the non-outline through cuts. This was an oversight that surprisingly has never been noticed until recently. We will change the pre-ramp to cut to operation depth when the pre-ramp is too large. It has always been set to not do a pre-ramp in this circumst...
by Larry Epplin
Fri, Sep 11 2009, 12:31PM
Forum: eCabinet Systems Software
Topic: SB Link Tenon Dado Cut Direction
Replies: 15
Views: 2487

Re: SB Link Tenon Dado Cut Direction

Gary,

This is an issue for the ShopBot Link to handle cutting characteristics of a ShopBot. There are no cutting direction settings in eCabinetSystems.
by Larry Epplin
Fri, Sep 11 2009, 8:46AM
Forum: eCabinet Systems Software
Topic: SB Link Tenon Dado Cut Direction
Replies: 15
Views: 2487

Re: SB Link Tenon Dado Cut Direction

It appears that the correct solution would be the ability to set a direction for dados/pockets. Then you can specify your maximum depth if you wish to complete the cutting in more than 1 pass to reduce load. This will allow you to keep the ability to run your outlines in the climb then conventional ...
by Larry Epplin
Fri, Aug 28 2009, 7:35AM
Forum: eCabinet Systems Software
Topic: Cabinet back full dado with scribe
Replies: 9
Views: 1209

Re: Cabinet back full dado with scribe

To get it to show graphically in eCabinets Kerry's suggestion is the way to go, however, this will created an 1/8" wide pocket at the machine which means an additional operation. If you would like it do be done in 1 operation per dado then Brian's suggestion is the way to go. By using Fit Clear...
by Larry Epplin
Fri, Aug 21 2009, 3:38PM
Forum: eCabinet Systems Software
Topic: ShopBot Link Update (1.0.13)
Replies: 4
Views: 637

Re: ShopBot Link Update (1.0.13)

That is a feature not used in ShopBot Link. We need to remove it. Please ignore.
by Larry Epplin
Fri, Aug 21 2009, 2:40PM
Forum: eCabinet Systems Software
Topic: ShopBot Link Update (1.0.13)
Replies: 4
Views: 637

Re: ShopBot Link Update (1.0.13)

no problem
by Larry Epplin
Fri, Aug 21 2009, 10:26AM
Forum: eCabinet Systems Software
Topic: ShopBot Link Update (1.0.13)
Replies: 4
Views: 637

ShopBot Link Update (1.0.13)

The latest version of ShopBot Link is 1.0.13. It's available at the following link.

http://www.thermwood.com/updates/update ... t_link.htm
by Larry Epplin
Fri, Jul 24 2009, 3:43PM
Forum: eCabinet Systems Software
Topic: claen up setting for dadoes-Shopbot
Replies: 2
Views: 538

Re: claen up setting for dadoes-Shopbot

The clean up pass will only be used in dado's when the tool is too small to perform the dado in 2 passes. This will invoke the pocketing routine where the clean up pass exists. To loosen your dado size you should adjust your dado width clearance setting in eCabinets Systems - Cabinet Editor - Constr...
by Larry Epplin
Tue, Jul 14 2009, 2:40PM
Forum: eCabinet Systems Software
Topic: Will ecab v6 support multi core processor
Replies: 3
Views: 627

Re: Will ecab v6 support multi core processor

Version 6 will support these operating systems. Some of the 3rd party applications in eCabinet Systems provided some improvements for multiple core processors, but the avantages have not been proven to be significant. The areas affected are Presentation View and Cabinet Regeneration. While Version 6...
by Larry Epplin
Mon, Jul 13 2009, 8:01AM
Forum: eCabinet Systems Software
Topic: What about Ecabinets
Replies: 5
Views: 1063

Re: What about Ecabinets

Hi Gary. Yes, eCabinet Systems is in the development phase for version 6. This version will include the ability to edit drawer box parts in the Part Editor. We plan to be in the beta testing phase for this version very soon.
by Larry Epplin
Mon, Jul 13 2009, 7:58AM
Forum: eCabinet Systems Software
Topic: ShopBot Link - tabs or skin - which takes precedence
Replies: 4
Views: 665

Re: ShopBot Link - tabs or skin - which takes precedence

Hi Don. The 2 features work independently. You can have both tabs and leave a skin at the same time.
by Larry Epplin
Thu, Jul 02 2009, 2:05PM
Forum: eCabinet Systems Software
Topic: ShopBot Link nesting effectiveness
Replies: 15
Views: 1810

Re: ShopBot Link nesting effectiveness

You are right Don. That is interesting. I have loaded your settings and I get the nest you displayed originally in this post by clicking the button Y. From what you are saying you get it by clicking the button X. I do not have an answer for that at all. With the Cut Line option in the next version I...
by Larry Epplin
Thu, Jul 02 2009, 8:41AM
Forum: eCabinet Systems Software
Topic: ShopBot Link nesting effectiveness
Replies: 15
Views: 1810

Re: ShopBot Link nesting effectiveness

Neville, Ok, I think I am grasping what you want. There is access to the OffFalls for this purpose. In Add Sheet(s) click the OffFalls button. This brings up a list of all the Off-Fall generated on that machine. This list currently contains ID, Date of creation, and Material Name. If we worked on ad...

Go to advanced search