Search found 174 matches

by Terry Davis
Mon, Mar 17 2008, 4:13PM
Forum: Thermwood 3-Axis Machinery
Topic: Warm up Program
Replies: 21
Views: 7909

Re: Warm up Program

Did I miss something at training? Why do you need a warm up program? As far as oiling goes ours oils to much, I'm always wiping oil off the machine sides.
by Terry Davis
Tue, Mar 11 2008, 4:59PM
Forum: eCabinet Systems Software
Topic: Software replacement
Replies: 7
Views: 1577

Re: Software replacement

Would that be the nice lady at the front entrance to Thermwood who has a little disk making factory under her desk and always a bowl of good candy?
by Terry Davis
Thu, Mar 06 2008, 12:59PM
Forum: eCabinet Systems Software
Topic: Crypt Acquire error.
Replies: 4
Views: 1942

Crypt Acquire error.

I did the DAOinstall off the install disk as suggested in my last post and I'm still getting the Crypt Acquire error during creation off the TWD file. It doesn't happen every time, usually it's every third or fourth file creation.
by Terry Davis
Thu, Mar 06 2008, 11:39AM
Forum: eCabinet Systems Software
Topic: Ecabinets Course Manual
Replies: 11
Views: 3231

Re: Ecabinets Course Manual

I took the course last November and have the Sept 2007 manual, it is very helpful as reference because it is more of a manual.
by Terry Davis
Wed, Mar 05 2008, 3:53PM
Forum: Thermwood 3-Axis Machinery
Topic: Thermwood and circle top.
Replies: 5
Views: 1711

Re: Thermwood and circle top.

Thanks guys got it working, I was using the break command to break the circle, once I used two arcs it was fine!
by Terry Davis
Wed, Mar 05 2008, 2:11PM
Forum: Thermwood 3-Axis Machinery
Topic: Thermwood and circle top.
Replies: 5
Views: 1711

Re: Thermwood and circle top.

When I break the circle into arcs I get the error " A common close point was not found for an outline operation" if I remember right all outlines have to be a closed entity.
by Terry Davis
Wed, Mar 05 2008, 1:53PM
Forum: Thermwood 3-Axis Machinery
Topic: Thermwood and circle top.
Replies: 5
Views: 1711

Thermwood and circle top.

We are trying to cut out a 48" dia. table top out of 1 1/8 material. We are sending this to the machine as a DXF file when loading and selecting my material I get an error that says"The material selected for the Dxf part D:\ -part name- has the incorrect thickness the required thickness re...
by Terry Davis
Fri, Feb 15 2008, 7:14PM
Forum: Customer Images
Topic: Hidden sound system
Replies: 2
Views: 2838

Re: Hidden sound system

Nice job Francis, where did you get the heat sensor your fans?
by Terry Davis
Thu, Feb 14 2008, 9:06PM
Forum: Thermwood 3-Axis Machinery
Topic: Flip Op jig?
Replies: 3
Views: 1754

Re: Flip Op jig?

Thanks for the reply Dan, before you replied I found the M999 macro in the macros folder of the c drive, I opened it and made the changes there and saved the file, I don't know if that was the proper way but it seemed to have worked because the values where there when I did it your way.
by Terry Davis
Wed, Feb 13 2008, 2:43PM
Forum: Thermwood 3-Axis Machinery
Topic: Flip Op jig?
Replies: 3
Views: 1754

Flip Op jig?

When the tech set up our machine we cut our own jig out of plywood, now we want to make a new one and don't know where he entered the X,Z values for the G902 location, I remember him block stepping on something then entering the values?
by Terry Davis
Thu, Feb 07 2008, 11:27AM
Forum: eCabinet Systems Software
Topic: Frameless Island Cabinet
Replies: 1
Views: 919

Frameless Island Cabinet

I'm building an island cabinet 130" long 24" deep made up of sink cabinets (false fronts & doors) that have to be accessed from both sides. How do I get doors, toekicks and false fronts on the back sides? The reason I need false fronts is to hide lights to illuminate bottles that are g...
by Terry Davis
Sat, Feb 02 2008, 10:02AM
Forum: eCabinet Systems Software
Topic: Dovetail Drawer settings
Replies: 3
Views: 1315

Dovetail Drawer settings

In the drawer box designer, drawer box construction setting, global settings what should the settings be for dovetail drawers be (being cut out of 1/2" baltic birch). There is 10 empty boxes to fill in! This is our first attempt at dovetail drawers..
by Terry Davis
Thu, Jan 31 2008, 10:46AM
Forum: Thermwood 3-Axis Machinery
Topic: Nesting update?
Replies: 7
Views: 2034

Re: Nesting update?

Ryan, we spoke in depth about this two weeks ago with Pete Riddle and he said there would be an update coming out to correct the issue, that is why I asked about the nesting update, is there an update being released to correct the HHP issue?
by Terry Davis
Wed, Jan 30 2008, 5:43PM
Forum: Thermwood 3-Axis Machinery
Topic: Nesting update?
Replies: 7
Views: 2034

Nesting update?

Was the control nesting update released on Tuesday the update that was supposed to fix our Arc teach on our handheld (shift +7) or is there another update coming out because this one had no effect on the HHP problem.
by Terry Davis
Wed, Jan 30 2008, 5:38PM
Forum: eCabinet Systems Software
Topic: Crypt Acquire error !
Replies: 2
Views: 815

Crypt Acquire error !

Every third or fourth time I try to create a Twd file I get the "CryptAcquireContext" error. I close Ecabs, delete the Microsoft\crypto\RSA subdirectories then run the thmcrpyt.exe file and things will be fine for a day or two. I learned how to fix this watching the tech that set our machi...

Go to advanced search