Search found 431 matches

by Nat Wheatley
Sun, Jul 08 2018, 9:25AM
Forum: eCabinet Systems Software
Topic: Flip Ops in SB Link
Replies: 12
Views: 12150

Re: Flip Ops in SB Link

Thanks Ralph. What was throwing me off is that just the face side of the piece displays, regardless of which side is being machined. That seems odd to me and will take some getting used to. You've had success using the flip ops first for whole sheets? I tried to do that when the Link first came out,...
by Nat Wheatley
Sat, Jul 07 2018, 2:56PM
Forum: eCabinet Systems Software
Topic: Flip Ops in SB Link
Replies: 12
Views: 12150

Re: Flip Ops in SB Link

Trying some things with this on my computer at home (not hooked to machine) and not having much luck. On the attached cabinet I select just the partition. If I nest it with 'Cut Flip Ops First' either selected, or not selected it lays out the part the same either way (all the operations are in the s...
by Nat Wheatley
Sat, Jul 07 2018, 5:05AM
Forum: eCabinet Systems Software
Topic: Flip Ops in SB Link
Replies: 12
Views: 12150

Re: Flip Ops in SB Link

Ralph,

In thinking further, I'm realizing that likely is the answer. I'll give it a try next time I'm in the shop.

Thanks for the help.

Nat
by Nat Wheatley
Fri, Jul 06 2018, 2:44PM
Forum: eCabinet Systems Software
Topic: Flip Ops in SB Link
Replies: 12
Views: 12150

Re: Flip Ops in SB Link

Thanks Ralph. I’ve looked through the Link again, and what I still can’t figure out is how to select the flip operations for a single part. I’m thinking there must be a way, as if ‘flip ops first weren’t selected you’d need to be able to do what I’m
looking to do.
by Nat Wheatley
Fri, Jul 06 2018, 9:00AM
Forum: eCabinet Systems Software
Topic: Nesting Error
Replies: 10
Views: 10192

Re: Nesting Error

Sorry,realized yesterday that it was a bad RTA pattern on the back stretcher that was causing the issue (Posted here yesterday but the message didn’t seem to take...)

Thanks to all for the input.

Nat
by Nat Wheatley
Thu, Jul 05 2018, 1:52PM
Forum: eCabinet Systems Software
Topic: Flip Ops in SB Link
Replies: 12
Views: 12150

Flip Ops in SB Link

I should know this already, but how do I pull up the flip ops for a single part in SB Link. The part is cut, with the operations done to the face of it, looking to set it back on the machine and have the drilling etc be done for the back side? I've had a work around for this up until now, be need to...
by Nat Wheatley
Thu, Jul 05 2018, 1:44PM
Forum: eCabinet Systems Software
Topic: Nesting Error
Replies: 10
Views: 10192

Re: Nesting Error

Thank you, email sent.
by Nat Wheatley
Thu, Jul 05 2018, 12:48PM
Forum: eCabinet Systems Software
Topic: Nesting Error
Replies: 10
Views: 10192

Re: Nesting Error

Hi, I put in that small dimension (.25mm) to keep the two pockets (different depths) separate. I’ve had issues in the past with two pockets touching, the seem to melt together, and throw the constraints off. The .25 is small enough that it gets cut away regardless. I hadn’t realized you were running...
by Nat Wheatley
Thu, Jul 05 2018, 12:30PM
Forum: eCabinet Systems Software
Topic: Nesting Error
Replies: 10
Views: 10192

Re: Nesting Error

Just not sure how, won’t allow me to attach .twd file?
by Nat Wheatley
Thu, Jul 05 2018, 11:59AM
Forum: eCabinet Systems Software
Topic: Nesting Error
Replies: 10
Views: 10192

Nesting Error

When I try to nest the attached cabinet using SB Link, I get the error messages:

'Couldn't find tool to work for pocket operation 3 on side 1 1 '

'Couldn't find tool to work for pocket operation 24 on side 4 1 '

Not sure how to attach the TWD file...
by Nat Wheatley
Tue, Jul 03 2018, 9:14AM
Forum: eCabinet Systems Software
Topic: Slow Cabinet
Replies: 17
Views: 16515

Re: Slow Cabinet

Takes 40 seconds here...
by Nat Wheatley
Tue, Jul 03 2018, 6:42AM
Forum: eCabinet Systems Software
Topic: Slow Cabinet
Replies: 17
Views: 16515

Re: Slow Cabinet

I've removed everything from my computer that I can, updated drivers etc. Cabinet is still just as slow as it was.

FWIW, I did notice that removing the 3 adjustable shelves (which place the shelf holes top to bottom) cuts the processing time in half), but all the units will have these shelves...
by Nat Wheatley
Fri, Jun 29 2018, 9:12PM
Forum: eCabinet Systems Software
Topic: Slow Cabinet
Replies: 17
Views: 16515

Re: Slow Cabinet

Got it, thank you!
by Nat Wheatley
Fri, Jun 29 2018, 8:10PM
Forum: eCabinet Systems Software
Topic: Slow Cabinet
Replies: 17
Views: 16515

Re: Slow Cabinet

Hi Scott, I do that somewhat periodically, but will try it in the morning and see if it helps any. Thank you There’s definitely something bogging down the computer, as it probably takes 10mins to restart after being turned off. I realize that’s probably sounds absurd to most, I’ll admit to not being...
by Nat Wheatley
Fri, Jun 29 2018, 7:21PM
Forum: eCabinet Systems Software
Topic: Slow Cabinet
Replies: 17
Views: 16515

Re: Slow Cabinet

The computer does seem clunky with just about everything I build, though it’s been bearable until this. This cabinet is more complex than what I normally do, but it will be a typical cabinet going forward. It’s got quite a few part editor cuts to accommodate leg levelers, and many more parts than no...

Go to advanced search