Search found 429 matches

by Nat Wheatley
Fri, Jun 29 2018, 6:19PM
Forum: eCabinet Systems Software
Topic: Slow Cabinet
Replies: 17
Views: 287

Re: Slow Cabinet

If you then click on 'Construction Settings' the press 'OK', it takes about 40 seconds (for me) for the cabinet to rebuild.
by Nat Wheatley
Fri, Jun 29 2018, 5:22PM
Forum: eCabinet Systems Software
Topic: Slow Cabinet
Replies: 17
Views: 287

Slow Cabinet

The attached cabinet takes a fairly long time to regenerate in the cabinet editor (about 40seconds on my computer). Its a version of a cabinet that I'll be working with daily, so I'm wondering if there's anything I can do/change to speed things up. Thank you for any help.

3 Section.hsf
(3.79 MiB) Downloaded 12 times
by Nat Wheatley
Thu, Jun 28 2018, 6:15PM
Forum: eCabinet Systems Software
Topic: Sloped Ceiling
Replies: 3
Views: 109

Re: Sloped Ceiling

Thanks very much Tim. Is there a way to also add in the actual ceiling?
by Nat Wheatley
Thu, Jun 28 2018, 3:05PM
Forum: eCabinet Systems Software
Topic: Sloped Ceiling
Replies: 3
Views: 109

Sloped Ceiling

Can anyone point me in the direction of where to learn how to draw a sloped ceiling?
by Nat Wheatley
Wed, Jun 27 2018, 5:33AM
Forum: eCabinet Systems Software
Topic: In Need of Tall Frameless Cabinet
Replies: 5
Views: 166

Re: In Need of Tall Frameless Cabinet

Thanks Tim!
by Nat Wheatley
Tue, Jun 26 2018, 10:46AM
Forum: eCabinet Systems Software
Topic: In Need of Tall Frameless Cabinet
Replies: 5
Views: 166

Re: In Need of Tall Frameless Cabinet

Ok, thanks. I wasn't sure if I'd be able to add crown molding to a base cabinet. I'm just getting into the drawing side of the program, and haven't explored adding moldings yet...

Nat
by Nat Wheatley
Mon, Jun 25 2018, 1:35PM
Forum: eCabinet Systems Software
Topic: Resized Tall Cabinet Elevated off of Floor
Replies: 2
Views: 142

Re: Resized Tall Cabinet Elevated off of Floor

Thanks a million, Forrest. Thats just what I was looking for.

Nat
by Nat Wheatley
Sun, Jun 24 2018, 1:42PM
Forum: eCabinet Systems Software
Topic: Resized Tall Cabinet Elevated off of Floor
Replies: 2
Views: 142

Resized Tall Cabinet Elevated off of Floor

(New to the drawing part of the program...) I draw a wall, switch to Elevation/Wall View. I place two 96" high Tall Cabinets, and they both sit correctly on the floor. I take one of those into the cabinet editor, change the height to 72" but when I bring it back into the room, it appears t...
by Nat Wheatley
Sun, Jun 24 2018, 1:31PM
Forum: eCabinet Systems Software
Topic: In Need of Tall Frameless Cabinet
Replies: 5
Views: 166

Re: In Need of Tall Frameless Cabinet

Nevermind...found the libraires online...
by Nat Wheatley
Sun, Jun 24 2018, 1:17PM
Forum: eCabinet Systems Software
Topic: In Need of Tall Frameless Cabinet
Replies: 5
Views: 166

In Need of Tall Frameless Cabinet

Does anyone have a tall frameless cabinet that I can use? There isn't one in my Standard Cabinet Library for some reason.
by Nat Wheatley
Thu, Apr 19 2018, 12:20PM
Forum: eCabinet Systems Software
Topic: Suggestions on how to drill three sets of shelf pin holes
Replies: 9
Views: 564

Re: Suggestions on how to drill three sets of shelf pin holes

For the middle row, add a second 'phantom' shelf. Set one of the rows to be off of the part (-3mm), set the other row where you need it to be.
by Nat Wheatley
Sat, Feb 17 2018, 10:38AM
Forum: eCabinet Systems Software
Topic: Shopbot Link looses zero to table after bit change
Replies: 5
Views: 692

Re: Shopbot Link looses zero to table after bit change

I'm with Don on this one, as I've not had that happen.

I had years of comm errors, causing various issues. Once I switched from Dell control computers to HP, the errors went away.
by Nat Wheatley
Mon, Jan 29 2018, 9:44AM
Forum: eCabinet Systems Software
Topic: Ladder Toekick
Replies: 2
Views: 475

Re: Ladder Toekick

Thanks Tim, I do need to be able to resize. The one I'm working on was made from a cabinet, but I used different parts than you listed (the part with the cutouts is the cabinet back). Insetting the back caused the cutout constraints to act oddly and/or disappear. I'll try it using the parts you ment...
by Nat Wheatley
Sun, Jan 28 2018, 10:52AM
Forum: eCabinet Systems Software
Topic: Ladder Toekick
Replies: 2
Views: 475

Ladder Toekick

I'm trying to come up with a simple ladder base for our closet systems. They typically need to be 2 1/2" tall, so I'm looking to avoid too many small pieces, as our vaccuum hold down doesn't do well with these. Also looking to minimize assembly time. I've attached a photo of what I'm coming up ...
by Nat Wheatley
Sat, Dec 16 2017, 10:05AM
Forum: eCabinet Systems Software
Topic: drawer slide locations
Replies: 8
Views: 2228

Re: drawer slide locations

Has anyone found a way to do this?

Go to advanced search