Search found 388 matches

by Nat Wheatley
Thu, Jun 11 2009, 6:38PM
Forum: eCabinet Systems Software
Topic: Label for Cabinets?
Replies: 2
Views: 496

Label for Cabinets?

Is there a way to generate a label for each cabinet in a room? (Not parts, but completed units?)
by Nat Wheatley
Wed, Jun 10 2009, 6:56PM
Forum: eCabinet Systems Software
Topic: The operation performed...violate...
Replies: 5
Views: 937

Re: The operation performed...violate...

Chris, no end boring, the holes are just pilot holes for screws which self drill into the ends of the decks and tops. I've oversized the holes for clarity (4mm). The drill I use for the holes is also setup in the software as 4mm, even though the bit is actually smaller than that.

Nat
by Nat Wheatley
Wed, Jun 10 2009, 3:31PM
Forum: eCabinet Systems Software
Topic: The operation performed...violate...
Replies: 5
Views: 937

Re: The operation performed...violate...

Chris, for the deck and top pilot holes, I just modified an RTA hole pattern, to include only the hole for the stud. Then just adjusted the diameter and location of the hole. Then you're just dealing with the RTA settings to get the hole depth. So far, I like it...

Nat
by Nat Wheatley
Tue, Jun 09 2009, 7:46PM
Forum: eCabinet Systems Software
Topic: The operation performed...violate...
Replies: 5
Views: 937

The operation performed...violate...

I keep getting this error message in PE: 'The operation performed on the current part violate the ideal tenons or dadoes. You might see some unexpected results' I've gotten it on several, distinct cabinets, and it seems to be come up when there are holes for the adjustable shelves. It has caused the...
by Nat Wheatley
Wed, Jun 03 2009, 5:33PM
Forum: eCabinet Systems Software
Topic: Assembly Screw Holes
Replies: 2
Views: 530

Re: Assembly Screw Holes

Chris, On the RTA fittings, I took the stud out of the hole pattern and things were fine. I hadn't had a problem with the RTA fittings themselves, but when the shelf holes were added, things were acting up. The fact that they were in line with each other (never overlapped) may have contributed. I ha...
by Nat Wheatley
Tue, Jun 02 2009, 5:20PM
Forum: eCabinet Systems Software
Topic: Assembly Screw Holes
Replies: 2
Views: 530

Assembly Screw Holes

Is there a way to limit a stretcher to have just one RTA fitting per end? I may go the route of using a piece of RTA hardware with a modified hole pattern to generate my pilot holes (thanks to Joe Dusel for the suggestion!), but need to iron this part of it out. All I'm coming up is to set the front...
by Nat Wheatley
Mon, Jun 01 2009, 8:16PM
Forum: eCabinet Systems Software
Topic: Wish List for Version 6
Replies: 6
Views: 1005

Re: Wish List for Version 6

I'd to see this also, and was a little suprised to find that this option didn't exist. Another drawback with using the adjustable shelf to create the holes is that I've had the shelf inadvertantly shift. Not a real problem if you're just using the holes for shelves, but definitely an issue if you're...
by Nat Wheatley
Mon, Jun 01 2009, 5:24PM
Forum: eCabinet Systems Software
Topic: Error with Shelf Holes
Replies: 10
Views: 1031

Re: Error with Shelf Holes

Kerry, I do think the error is coming about within E-cabinets. I changed a number of things back and forth, but think that the error message within PE, was consistant with the parts that were drilled incorrectly. I cut the parts today, eliminating the stud from the hole pattern for the RTA fitting, ...
by Nat Wheatley
Sun, May 31 2009, 2:05PM
Forum: eCabinet Systems Software
Topic: Error with Shelf Holes
Replies: 10
Views: 1031

Re: Error with Shelf Holes

Nick, No setting for max. step depth. Something's buggy. This cabinet was just one in nest a nest of several, all had the same shelf hole depth, and this is the only one that ended up getting drilled twice. This is the only one thatI used a shelf to generate the shelf holes for, though. I've added s...
by Nat Wheatley
Sun, May 31 2009, 9:18AM
Forum: eCabinet Systems Software
Topic: Error with Shelf Holes
Replies: 10
Views: 1031

Re: Error with Shelf Holes

Thanks Kerry. I have a Shopbot, and I was treading water, trying every route I could think of to avoid paying the $22K to for the CNC add on to my CabinetVision software. Then along came the SB/E-Cabinets Link. I hadn't used E-Cabs before, but ordered it when I heard of the Link becoming available, ...
by Nat Wheatley
Sun, May 31 2009, 6:24AM
Forum: eCabinet Systems Software
Topic: Error with Shelf Holes
Replies: 10
Views: 1031

Re: Error with Shelf Holes

On the CNC it's drilling each row of holes twice.

The RTA fittings for the top have a stud that was in line with the shelf holes, which seemed to be causing the problem. I can use the shelf holes for all my RTA studs and sidestep the issue, for now...
by Nat Wheatley
Sat, May 30 2009, 7:38AM
Forum: eCabinet Systems Software
Topic: Error with Shelf Holes
Replies: 10
Views: 1031

Error with Shelf Holes

On the attached cabinet, each row of shelf holes is getting drilled twice, for some reason. When I have one of the sides in PE, then go to return to the Cab. Editor, I get the message "The operation... violates the ideal tenon or dadoes. You may see some unexected results". (There are no t...
by Nat Wheatley
Sat, May 30 2009, 2:37AM
Forum: eCabinet Systems Software
Topic: Metabox drawers HELP
Replies: 10
Views: 1746

Re: Metabox drawers HELP

That worked. Thanks Chris.
by Nat Wheatley
Fri, May 29 2009, 6:01PM
Forum: eCabinet Systems Software
Topic: Metabox drawers HELP
Replies: 10
Views: 1746

Re: Metabox drawers HELP

Once I open it in the display part editor, how do I get the drawers to show?
by Nat Wheatley
Fri, May 29 2009, 4:40PM
Forum: eCabinet Systems Software
Topic: Metabox drawers HELP
Replies: 10
Views: 1746

Re: Metabox drawers HELP

How do I open the posted file(HSF)?

Go to advanced search