Search found 430 matches

by Nat Wheatley
Tue, Jan 10 2017, 2:01PM
Forum: eCabinet Systems Software
Topic: Frameless Corner Cabinet with Angled Front
Replies: 3
Views: 1933

Re: Frameless Corner Cabinet with Angled Front

My vote would be for an option to add material to the sides, if desired.

It's very odd that it's factored in automatically, without any indication of it doing so. It's a mistake waiting to happen.
by Nat Wheatley
Mon, Jan 09 2017, 6:33PM
Forum: eCabinet Systems Software
Topic: Frameless Corner Cabinet with Angled Front
Replies: 3
Views: 1933

Frameless Corner Cabinet with Angled Front

Can someone tell me why the software extends the depth on this type of cabinet by the thickness of the side panels? I enter a left and right depth of 304 and it produces parts for a 323 deep cabinet. The only thing I can think of it that it allows for the sides to be trimmed at the same angle to mat...
by Nat Wheatley
Wed, Dec 28 2016, 11:11AM
Forum: eCabinet Systems Software
Topic: Thank you for 'No Drilling'
Replies: 0
Views: 1595

Thank you for 'No Drilling'

Just used this option in the SBLink and it helped me salvage a sheet that I had mistakingly run with 'no outline cuts' selected. Thanks very much for adding this feature in.
by Nat Wheatley
Sun, Dec 04 2016, 2:47PM
Forum: eCabinet Systems Software
Topic: Oversized Holes
Replies: 5
Views: 2397

Re: Oversized Holes

Thanks very much for the feedback, I'll take a look at the machine tomorrow. What's odd is that it comes and goes, and when it does happen it's confined to a single job, but happens all throughout that job.
by Nat Wheatley
Sun, Dec 04 2016, 12:46PM
Forum: eCabinet Systems Software
Topic: Oversized Holes
Replies: 5
Views: 2397

Re: Oversized Holes

Hi, same material used from job to job, no changes in the link settings. The same bit is used for multiple jobs. One job (most) will be fine, then on the next, all the 8mm holes are oversized, then the next job they're fine again.
by Nat Wheatley
Sun, Dec 04 2016, 9:59AM
Forum: eCabinet Systems Software
Topic: Oversized Holes
Replies: 5
Views: 2397

Oversized Holes

I'm having an issue machining the RTA pattern shown in the attached photo. The pattern has an 8mm through hole cut in the field of the 20mmhole, which allows the fitting to be tightened from both side of the part. This hole then gets a covered with cap which has an 8mm stem that fits into the hole. ...
by Nat Wheatley
Mon, Sep 12 2016, 5:25PM
Forum: eCabinet Systems Software
Topic: Shopbot Link approaching almost 3.5 years since last update
Replies: 13
Views: 5296

Re: Shopbot Link approaching almost 3.5 years since last update

Would it be possible to add the option 'No Drillings' similar to 'No Outline Cuts'? From time to time I've had to stop the machine mid sheet (broken bit, glitch etc), and in order to continue needed to run the entire sheet again. Where many of our parts have full line boring, and the drilling is don...
by Nat Wheatley
Mon, Jun 06 2016, 9:04AM
Forum: eCabinet Systems Software
Topic: SB Link Printer Setup
Replies: 13
Views: 5323

Re: SB Link Printer Setup

Thanks very much. I'm going to hook up my old control computer later on today (hopefully) and take a look at how things are setup there.
by Nat Wheatley
Mon, Jun 06 2016, 5:44AM
Forum: eCabinet Systems Software
Topic: SB Link Printer Setup
Replies: 13
Views: 5323

Re: SB Link Printer Setup

Most recent version of the Link is installed so not clear why it's not remembering my printer selection.
by Nat Wheatley
Fri, Jun 03 2016, 4:37PM
Forum: eCabinet Systems Software
Topic: SB Link Printer Setup
Replies: 13
Views: 5323

Re: SB Link Printer Setup

Should be the most recent version, but I'll check in the morning. I do still have the old control computer, so may take a look on there to see how things were setup. Thanks
by Nat Wheatley
Fri, Jun 03 2016, 4:06PM
Forum: eCabinet Systems Software
Topic: SB Link Printer Setup
Replies: 13
Views: 5323

Re: SB Link Printer Setup

Those are the steps I'm following too, but it's not remembering the printer I'm choosing to print the labels for some reason.
by Nat Wheatley
Fri, Jun 03 2016, 3:37PM
Forum: eCabinet Systems Software
Topic: SB Link Printer Setup
Replies: 13
Views: 5323

Re: SB Link Printer Setup

I've got PDF factory setup as my default printer, because I believe if I setup the Dymo printer as default, then the extra steps would just switch over to printing the sheet layouts when I went to print those.
by Nat Wheatley
Fri, Jun 03 2016, 5:32AM
Forum: eCabinet Systems Software
Topic: SB Link Printer Setup
Replies: 13
Views: 5323

Re: SB Link Printer Setup

Does anyone know how to do this (Thermwood?) There's 9 keystrokes involved in manually selecting the printer and printing labels...
by Nat Wheatley
Fri, Apr 08 2016, 9:47AM
Forum: eCabinet Systems Software
Topic: SB Link Printer Setup
Replies: 13
Views: 5323

Re: SB Link Printer Setup

Anyone? It can be done, I had it setup correctly on my old computer, but have just replaced it.

Go to advanced search