Search found 389 matches

by Nat Wheatley
Tue, Dec 31 2013, 5:39PM
Forum: eCabinet Systems Software
Topic: How to Go Back a Version?
Replies: 3
Views: 918

How to Go Back a Version?

Can anyone tell me how I can revert from Built 12(beta) to Build 11? Build 12 expires at the end of the day today, and I have work I need to do with the software tomorrow.
by Nat Wheatley
Tue, Oct 08 2013, 5:17PM
Forum: eCabinet Systems Software
Topic: Metal Drawer Systems
Replies: 12
Views: 3479

Re: Metal Drawer Systems

Thanks very much Fred. I've used piles of Zargen slides usual manual boring, but had forgotten all the settings. Slowly climbing back up their learning curve...

Agreed that once they're dialed in, their assembly speed in unbeatable.
by Nat Wheatley
Mon, Oct 07 2013, 4:26PM
Forum: eCabinet Systems Software
Topic: Metal Drawer Systems
Replies: 12
Views: 3479

Re: Metal Drawer Systems

Working now with the negative depth.
by Nat Wheatley
Mon, Oct 07 2013, 2:45PM
Forum: eCabinet Systems Software
Topic: Metal Drawer Systems
Replies: 12
Views: 3479

Re: Metal Drawer Systems

Thanks Dennis.
by Nat Wheatley
Mon, Oct 07 2013, 7:47AM
Forum: eCabinet Systems Software
Topic: Metal Drawer Systems
Replies: 12
Views: 3479

Re: Metal Drawer Systems

Thanks Kerry. I'll try the negative depth, it sounds like that may the problem. I was entering a positive depth (following the help file) with no luck.

Nat
by Nat Wheatley
Sat, Oct 05 2013, 12:53PM
Forum: eCabinet Systems Software
Topic: Metal Drawer Systems
Replies: 12
Views: 3479

Re: Metal Drawer Systems

I resorted to adding the holes in manually. It added the slide holes for the side members fine, but wouldn't add them in to the back of the drawer front, no matter what I did. I had to remove the front holes altogether from the slide pattern, as all though they weren't showing up, they were throwing...
by Nat Wheatley
Fri, Oct 04 2013, 1:53PM
Forum: eCabinet Systems Software
Topic: Temporary folder could not be found. Please check your PHP i
Replies: 1
Views: 1037

Temporary folder could not be found. Please check your PHP i

Trying to upload a file, and am getting this message. Anyone know what it means?
by Nat Wheatley
Fri, Oct 04 2013, 10:53AM
Forum: eCabinet Systems Software
Topic: Metal Drawer Systems
Replies: 12
Views: 3479

Re: Metal Drawer Systems

I've been trying that and the holes aren't showing up on the back of the drawer front for some reason. From what I can tell. I'm doing everything as the tutorial is showing to do it, but still can't get the holes to show up... FWIW, I'm using just drawer fronts (no drawer box) and trying to apply th...
by Nat Wheatley
Fri, Oct 04 2013, 9:46AM
Forum: eCabinet Systems Software
Topic: Metal Drawer Systems
Replies: 12
Views: 3479

Metal Drawer Systems

In what area of the software do I set up the drilling pattern for these? I read the help file, but wasn't sure where to actually start.

Thanks
by Nat Wheatley
Fri, Aug 23 2013, 5:38PM
Forum: eCabinet Systems Software
Topic: Flip ops
Replies: 13
Views: 2661

Re: Flip ops

Hard to say without seeing the cabinet, but have you tried setting the hole patterns to slightly more than 1/2 the material thickness? At one point (in at least the SB Link) I needed to set the depth of shelf holes more than 1/2 material depth to get them to drill through on partitions. There was an...
by Nat Wheatley
Sun, Jun 09 2013, 12:22PM
Forum: eCabinet Systems Software
Topic: KCD and Shopbot Link
Replies: 0
Views: 1101

KCD and Shopbot Link

I'm guessing that I cannot pull a file from KCD into the SBLink for machining is that correct?
by Nat Wheatley
Wed, Jun 05 2013, 5:45PM
Forum: eCabinet Systems Software
Topic: Turn Labels Off For Some Parts?
Replies: 0
Views: 992

Turn Labels Off For Some Parts?

It would be nice to be able to do this. Our drawer boxes are nested with all other closet parts. The drawer box parts never need labels as they're self explanatory. The labels for these parts are printed then end up in the trash, as they're not applied to parts. Not a huge deal, just seems a little ...
by Nat Wheatley
Mon, Apr 15 2013, 9:24AM
Forum: eCabinet Systems Software
Topic: Drawer with Stretcher?
Replies: 2
Views: 2277

Re: Drawer with Stretcher?

Thanks Scott. I've been on the verge of just switching to 3/4" bottom on my drawers, and just hearing that someone else does the same may be enough incentive to push me in that direction.

Nat
by Nat Wheatley
Sun, Apr 14 2013, 6:05PM
Forum: eCabinet Systems Software
Topic: Drawer with Stretcher?
Replies: 2
Views: 2277

Drawer with Stretcher?

Is there any way to add a stretcher (or partition) to a drawer? On larger drawers, we add a stretcher under the 1/4" bottom for additional support. I was hoping to be able to do this in the drawer box editor, but am not seeing the option available.

Thanks
by Nat Wheatley
Fri, Apr 05 2013, 4:02PM
Forum: eCabinet Systems Software
Topic: Angled Shelf
Replies: 6
Views: 1324

Re: Angled Shelf

Thanks Wally, I just saw this reply. This particular cabinet is just a single shelf, not top/bottom but I do like what you've shown for those shoe towers and will give that a try next one we have.

Nat

Go to advanced search